General Troubleshooting
Symptom
Solution(s)
Applies to
| Foggers |
| Dimmers |
Lights | & Snow | Controllers | & Chaser |
|
|
|
|
| Auto shut off | Check fan thermal switch reset | |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| Beam is very dim or | Clean optical system or replace lamp | |
|
|
|
| not bright | Check 220/110v switch for proper setting |
|
|
|
|
|
|
|
|
|
|
|
| Breaker/Fuse keeps | Check total load placed on device |
|
|
| |
| blowing |
|
|
|
|
|
|
|
|
|
|
|
|
| Chase is too slow | Check users manual for speed adjustment | |
| | |
|
|
|
|
|
|
|
| Device has no power | Check for power on Mains. | |
| | |
|
| Check device’s fuse. (internal and/or external) |
|
|
|
|
| Fixture is not | Check DMX DIP switch settings for correct addressing | |
|
|
|
| responding | Check DMX cables |
|
|
|
|
|
| Check polarity switch settings |
|
|
|
|
|
|
|
|
|
|
|
| Fixture is on but | Make sure you have the correct audio mode on the |
|
|
|
|
| there is no | control switches. If audio provided via ¼” jack, make | |
| | |
| movement to the | sure a live audio signal exists |
|
|
|
|
| audio | Adjust sound sensitivity knob |
|
|
|
|
|
|
|
|
|
|
|
| Lamps cuts off | Possible bad lamp or fixture is overheating. | |
|
|
|
| sporadically | Lamp may be at end of its life. |
|
|
|
|
|
|
|
|
|
|
|
| Light will not come | Some discharge lamps require a cooling off period | |
|
|
|
| on after power failure | before the electronics in the fixture can kick start it |
|
|
| |
|
|
|
|
| ||
|
| again, wait 5 to 10 minutes before powering up |
|
|
|
|
|
|
|
|
|
|
|
| Loss of signal | Use only DMX cables |
|
|
|
|
|
| Install terminator | | | | |
|
| Note: Keep DMX cables separated from power cables |
|
|
|
|
|
| or black lights. |
|
|
|
|
|
|
|
|
|
|
|
| Moves slow | Check 220/110v switch for proper setting | |
|
|
|
|
|
|
|
|
|
|
| No flash | |
|
|
| |
|
|
|
|
|
|
|
| No laser output | Bounce mirror motor may have shifted during shipping, | |
|
|
|
|
| readjust |
|
|
|
|
|
|
|
|
|
|
|
| No light output | Check slip ring & brushes for contact | |
|
|
|
|
| Install bulb |
|
|
| |
|
|
|
|
|
| |
|
| Call service technician |
|
|
|
|
|
|
|
|
|
|
|
| Relay will not work | Check reset switch |
|
|
| |
|
| Check cable connections |
|
|
|
|
|
|
|
|
|
|
|
| Remote does not | Make sure connector is firmly connected to device | | |
|
|
| work |
|
|
|
|
|
|
|
|
|
|
|
|
| Stand alone mode | All Chauvet lighting fixtures featuring |
|
|
|
|
|
| functions do not require additional settings, simply | |
|
|
|
|
| power the fixture and it will automatically enter into this |
|
|
| |
|
| mode |
|
|
|
|
|
|
|
|
|
|
|
If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page.
LED Mushroom™ User Manual | 15 | 7/24/2009 4:35 PM |