Control Maintenance

Maintenance

The Ikelite Digital Housing should be given the same care and attention as your other photographic equipment. In addition to normal maintenance we recommend that the housing be returned to Ikelite periodically to be checked and pressure tested.

1. Do Not leave the camera and housing in direct sunlight for prolonged periods. Heat may damage the camera.

2. Do Not ship the camera in the housing.set 3. Before using the housing, always check the tightness of the

screw in each control knob.

Check each control gland to make sure they are tight. There is a slight chance that either could vibrate loose during travel.

4. Keep the back o'ring clean and lightly lubricated. To lubricate remove the o'ring from the back. Put a small amount of lkelite lubricant on your fingers. Draw the o'ring through your fingers to apply a light coating of lubricant. Only apply enough lubricant to make the o'ring feel slick. Do Not stretch the o'ring. This light coating of lubricant will help to keep the o'ring from drying out and will help to show a dark sealing line when the housing back is properly sealed.

5. Keep the area where the o'ring fits and the sealing surface of the housing clean.

6. Rinse the housing exterior in fresh water after each salt water use. Dry with a soft cloth. Dry lens port to eliminate spotting. After several uses in salt water soak the housing in a mild soap solution, rinse and dry before storage. When storing the housing, remove the back o'ring, lightly lubricate and place in a plastic bag. Place the plastic bag with o'ring inside the housing for safe keeping.

CAUTION

Never use spray lubricants as the propellant ingredient can cause the plastic housing to crack.

Ikelite controls are designed to provide years of reliable service with minimal maintenance.

1. Push button controls require no maintenance other than rinsing in fresh water after saltwater use. If a push button control becomes difficult to push or if it sticks when depressed, soak the housing in luke warm fresh water. After a few minutes operate the push button. If this does not correct the problem, return the housing to Ikelite for maintenance.

2. Some of the controls have long shafts. These controls can be

lubricate shaft

housing

3.Some of the controls have a short shaft and cannot be pulled out exposing the shaft for lubrication. In the unlikely event one of these controls sticks or becomes difficult to operate you can remove the control from the housing and lubricate it, or return the housing to Ikelite for maintenance. To remove the control, loosen the set screw in the knob (allen wrench required); remove the knob. If there is salt or dirt build-up on the exposed control shaft, clean the shaft. Open the housing and gently slide the control shaft out of the control gland. Clean and lightly lubricate the shaft, including the end of the shaft. Slide the shaft back into the control gland and gently slide it back and forth a few times without fully removing the shaft from the gland. Replace the knob, NOTE the flat area on the shaft, the set screw in the knob should tighten down against the flat area on the control so the knob does not turn on the shaft.

pull out to expose shaft

pulled out, exposing the shaft (see drawing).

To lubricate the control, gently pull on the knob until the stainless steel shaft is exposed. Lightly lubricate the shaft, then move the shaft in and out several times. This will lubricate the x'ring in the Ikelite control gland. This should be done before using the housing after a prolonged storage period, or once a week when the housing is in use.

continued on next page

control	housing	gland
control	housing	gland
shaft

Flat Tighten set screw down against this area when

replacing the knob. Lubricate end of shaft before reinserting into gland

Loosen set screw (allen wrench required)

DSC-W50 specifications

The Ikelite DSC-W50 underwater housing is a remarkable accessory designed specifically for the Sony Cyber-shot DSC-W50 digital camera. This housing allows photographers and enthusiasts to take their photography experiences underwater, preserving the stunning beauty and diversity of marine life.

One of the main features of the Ikelite housing is its depth rating. It is robustly built to withstand depths of up to 130 feet (40 meters), making it ideal for both recreational scuba diving and snorkeling. The housing is crafted from durable polycarbonate materials, ensuring both crystal-clear visibility and protection against the corrosive effects of saltwater.

Accessibility is one of the defining characteristics of the Ikelite DSC-W50. The housing is designed with user-friendly controls that mirror the camera's functions, enabling easy adjustments even while wearing dive gloves. Photographers can effortlessly operate the shutter, zoom, and various settings without removing the camera, ensuring a seamless shooting experience.

In terms of technology, the housing incorporates a large clear front port for optimal image quality. This design minimizes distortion and allows for the full use of the camera’s lens capabilities. The Ikelite DSC-W50 is also compatible with various external flash systems, enhancing the ability to capture vibrant colors and details in deeper waters where natural light begins to diminish.

Another important aspect is the housing's ergonomic design. It features an easy-to-grip handle that provides stability during dives, which is crucial for capturing sharp images in challenging underwater conditions. For added versatility, a variety of accessories, including filters and lens ports, can be attached to cater to different shooting scenarios.

Moreover, the Ikelite DSC-W50 is designed to provide a reliable weather seal, safeguarding the camera from water ingress. With a form-fitting design, the housing ensures that the camera remains secure while still granting access to the camera’s battery and memory card compartments without the need to remove the housing.

In conclusion, the Ikelite DSC-W50 underwater housing combines durability, functionality, and advanced technology, making it an essential tool for underwater photographers. With its user-friendly features and impressive specifications, it opens up a world of creative possibilities, allowing you to capture breathtaking underwater moments with confidence and ease.