Silvercrest KH 2130 Device components, Putting the device into use, Connecting the transmitter

Page 8

The device components

Fig. A: The transmitter:

qTransmitter

wLED status indicator e Switch ROOM 1 r Switch ROOM 2

t Infrared connection socket (IR) y Output for a TV

u AV input 2 i AV input 1

o Connection socket

a Transmitter's on/off switch

s Transmitter channel toggle switch (on the underside of the device)

Fig. B: The receiver:

dReceiver

fInfrared receiver

gLED operating indicator

hAudio/Video CINCH outputs

jConnection socket for the supply voltage

kReceiver's on/off switch

lReception channel switch (bottom of device)

1( Wall plug transformer (2 pieces)

2) CINCH—3,5mm jacks cables (2 pieces) 2! SCART—CINCH adapter "IN"

2@ SCART—CINCH adapter "OUT"

2# Infrared cable with 3 transmit diodes 2$ AUDIO adapter 3.5 mm mini-stereo

to CINCH female

2% CINCH—CINCH cable

Putting the device into use

First take all device components from the packaging and remove all packing foil and tape.

Important notice:

Even when the system (transmitter + receiver) is switched off, the manufac- turer still recommends disconnecting the wall plug transformer from the mains power or using a power strip with a shut-off switch. Only in this way is complete switch off assured thus contributing to economical consumer attitude.

Connecting the transmitter

Note:

You can connect two signal sources. The signal to be transmitted can be selected via a switch on the front panel of the transmitter. Thereby the radio transmission set can transmit the image and sound signals of every de- vice that emits a sound and/or video signal via a suitable connection:

DVD Player / CD Player

VCR

Television

SAT receiver/set top box

Video camera

Computer video card, etc.

Connecting signal sources to the transmitter:

On devices with cinch outputs for the audio and video signals you connect these via one of the supplied CINCH— 3,5mm jack cables 2) to the socket "AV IN 1" i on the rear panel of the transmitter q.

- 6 -

Image 8
Contents Radio SET Gesundheit und Sicherheit gemäß § 3 1 1. Artikel 3 1 a Content Contents Intended UseRisk of electric shocks Technical dataSafety instructions Risk of fire Risk of suffocationRisk of accidents and injury Damage to the deviceConnecting the transmitter Device componentsPutting the device into use Important noticeInfrared connection Observe the colour codingConnecting the receiver Switching onTips Video card must have an Fbas output availableCleaning TroubleshootingImproving the transmission quality Expansion optionsImporter Disruptions in remote control commandsDisposal Important warranty information Processing number RMA number as well asPage Indholdsfortegnelse Side Anvendelsesområde Medfølger ved købPads til fastsætning af infrarøde sendedioder BetjeningsvejledningFare på grund af elektrisk stød Tekniske dataSikkerhedsanvisninger Fare for kvælning Info om afbrydelse fra strømmenBrandfare Fare på grund af radiosignaler Fare for ulykker og personskaderSkader på apparatet Brug ikke aggressive kemiske substan- ser til rengøringApparatets dele Opstart af apparatetTilslutning af senderen Vigtige informationer inden opstartInfrarød-forbindelse Tænd for signalkilden igen, og start evt. afspilningen Tilslutning af modtagerenSørg for, at farvetildelingen er rigtig VigtigtForbedring af overførselskvaliteten Kanalindstilling parallelfunktionRengøring UdvidelsesmulighederFejl ved fjernbetjeningskommandoerne BortskaffelseImportør Et administrationsnummer RMA- nummer samt Vigtige garantioplysninger