Yamaha NS-P220 owner manual For Canadian Customers, For U.K. and Europe models only

● Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipments. Never pull the wires themselves.

● Be sure to read the “TROUBLESHOOTING” section regarding common operating errors before concluding that the unit is faulty.

Never open the cabinet. If something drops into the set, contact your dealer.

●

● Do not place the speakers where they are liable to be knocked over or struck by falling objects. Stable placement will also ensure better sound performance.

● Placing the speakers on the same shelf or rack as the turntable can result in feedback.

● Any time you note distortion, reduce the volume control

on your amplifier to a lower setting. Never allow your amplifier to be driven into “clipping”. Otherwise the speakers may be damaged.

● When using an amplifier with a rated output power higher than the nominal input power of the speakers, care should be taken never to exceed the speakers’ maximum input.

● As these speakers contain strong magnets (though all of them are magnetically shielded types), avoid placing watches, magnetic tapes, etc. near them. Also, placing the speakers near a TV set may impair picture color. If this happens, move the speakers away from the TV set.

● Do not attempt to clean the speakers with chemical solvents as this might damage the finish. Use a clean, dry cloth.

● Secure placement or installation is the owner’s responsibility.

YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers.

For SW-P201 only

VOLTAGE

SELECTOR

● Do not place the speakers where foreign objects such as water drips might fall. It might cause a fire, damage to the speakers, and/or personal injury.

Thank you for selecting this YAMAHA NS-P220 Speaker Package.

CAUTION: Read this before operating your unit.

● To assure the finest performance, please read this manual	● When not planning to use this unit for a long period (ie.,
carefully. Keep it in a safe place for future reference.	vacation, etc.), disconnect the AC power plug from the
● Install the speakers in a cool, dry, clean place – away from	wall outlet.
windows, heat sources, sources of excessive vibration,	● To prevent lightning damage, disconnect the AC power
dust, moisture and cold. Avoid sources of humming	plug when there is an electric storm.
(transformers, motors). To prevent fire or electrical shock,	● Since this unit has a built-in power amplifier, heat will
do not expose the speakers to rain or water.
	radiate from the rear panel. Place the unit apart from the
● To prevent the enclosure from warping or discoloring, do
	walls, allowing enough space above, behind and on the
not place the speakers where they will be exposed to	both sides of the unit to prevent fire or damage.
direct sunlight or excessive humidity.	Furthermore, do not position with the rear panel facing
● Do not place the following objects on the speakers:	down on the floor or other surfaces.
Glass, china, etc.	<For U.K. and Europe models only>
If glass etc. falls by vibrations and breaks, it may cause	Be sure to allow a space of at least 20 cm above, behind
personal injury.	and on both sides of the unit.
A burning candle etc.	● Super-bass frequencies reproduced by this unit may
If the candle falls by vibrations, it may cause fire and	cause a turntable to generate a howling sound. In such a
personal injury.
	case, move this unit away from the turntable.
A vessel with water in it
	● If you hear distorted noise (i.e., unnatural, intermittent
If the vessel falls by vibrations and water spills, it may
	“rapping” or “hammering” sounds) coming from this unit,
cause damage to the speakers, and/or you may get an
	reduce the volume level. Extremely loud playing of a
electric shock.
	movie soundtrack’s low frequency, bass-heavy sounds or
	similarly loud popular music passages can damage this
	speaker system.

●VOLTAGE SELECTOR (General model only)

The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply.

Voltages are 110-120/220-240 V AC, 50/60 Hz.

220V-240V

110V-120V

Standby mode

If the POWER switch is set to the ON position and the AUTO STANDBY switch is set to the HIGH or LOW position, this unit turns into the standby mode when no signal is inputted to this unit.

In this state, this unit is designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

For Canadian Customers

To prevent electric shock, match wide blade of plug to wide slot and fully insert.

This Class B digital apparatus complies with Canadian ICES-003.

1