Rose electronic CTP-8S Static Ram Read/Write Test, Non-volatile Ram Tests, Front Panel Switches

Page 25

Static Ram Read/Write Test

The next test is for static ram. Since the Caretaker Plus has no static ram, this test is displayed as shown in TABLE 6 for consistency with other Rose products.

Non-volatile Ram Tests

The fourth and final power up test is for the non-volatile memory. A series of tests are performed. An error shown by the LEDs as error 4 indicates that the data in the nonvolatile memory has been corrupted. To attempt to rewrite the default parameters push SELECT switch then the ADVANCE switch. If the error condition goes out, the unit may be powered up again to see if it halts at error 4 again. If it still displays error 4, a fatal error has occurred and servicing is required. If the unit displays an error 45, the default parameters were not written correctly. This is a fatal error and servicing is required.

If the unit recovers from the error the configuration parameters have been returned to their default settings and the unit must be configured again if these default settings are unacceptable. This condition should not normally occur. If it does it indicates that possibly the unit has been subjected to a strong static discharge or surge on its incoming power or signal lines. The other possibility is an internal chip failure.

In addition to the data in the non-volatile ram, several others tests on the non-volatile ram are done. If any error 4 occurs and a reset to default does not correct it, the unit needs servicing. The additional errors listed below are for technical support purposes only.

Front Panel Switches

The front panel switches, labeled SELECT and ADVANCE, are used to enter and exit the configuration menu and to enter and exit the flow control display mode. These switches can be disabled under program control. This is done by either using the 'Operator Switch Disable' command or through the configuration menu. Note that if these switches are disabled and the setting is stored in non-volatile memory, the only way to re-enable the switches is by resetting the Caretaker Plus to the factory default settings. See the 'Diagnostics' section for more information.

Data LED, Busy LED, and Error LED

The DATA LED flickers when data is sent in or out the shared device's port. When large blocks of data are sent to or received from the shared device, the DATA LED will be on continuously. The BUSY LED lights when the shared device is telling Caretaker Plus not to send data. For parallel models only, the ERROR LED lights to indicate a printer error or device off-line.

Buffer Overflow Error Display (Serial Models Only)

If any device fails to follow flow control protocol and transmits data when the Caretaker Plus is instructing it not to, an overflow may occur. If this happens, the ERROR LED and the overflowed port's LED will flash rapidly in unison. If the overflow was on the input buffer for the shared device, the BUSY LED will flash along with the ERROR LED. This indicates a buffer overflow has occurred and data may have been lost. This display will remain until acknowledged by pressing the advance switch. Other than lost data on the overflowed port, operation of the unit is not affected by this display. If the buffer is not cleared, data transfer continues, but the data may be unreliable. If more than one port overflows, multiple port LEDs will flash in unison with the ERROR LED. When this display occurs, the cabling may be incorrect, or a program that uses only X-on/X-off flow control may be accessing a port that is configured for DTR flow control.

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL

21

 

Image 25
Contents Installation Operations Manual Page Limited Warranty Table of Contents Disclaimer FeaturesIntroduction First Steps Model Number and OptionsCaretaker Plus Front Panel Display Front Panel DisplaySerial Set-Up for PCs Mode LPT1+COM1Serial Set-up For Other Computers or Terminals Caretaker Plus Rear Panel Serial Model Parallel Set-Up Mode LPT1,,PCaretaker Plus Rear Panel Parallel Model Cabling ConfigurationParallel Cabling Serial CablingDisabled EnabledElectronics None DTRTimeout Configuration Menu ItemsProtocol Form Feed Disable Operator SwitchesInitialization String KeepExit Advanced FeaturesHelp Main Menu Unidirectional X-on/X-offAllow Timeout On Busy Ports Reverse Channel Data TimeoutFilter Characters Return To Previous MenuConfiguration Commands =DTR/DSR Protocol CommandInitialization String Command Parallel Enable Logic CommandGrounding Initial State OperationsNormal Operation Buffer Characteristics Printer Initialization Signal Parallel Models OnlyUnit Software Reset Function ExplanationCopy CON COM1CR TimeoutAdding More Memory Initialization StringChanging the Serial Baud Rate Program Checksum Test Power Up Initial DisplayBuffer Memory Sizing and Read/Write Test Data LED, Busy LED, and Error LED Front Panel SwitchesBuffer Overflow Error Display Serial Models Only Static Ram Read/Write TestFlow Control Display Mode Serial Models Only Troubleshooting TroubleshootingII. Nothing happens when sending data III. Garbled data received at shared devicePorts do not time out Technical Support Maintenance and RepairDiagnostic Modes DiagnosticsRestore To Factory Default Short TestSerial Units Print Configuration/Test Pattern FunctionParallel Units NoneLong Test Without Loopback Long Test with Loopback Loopback Test ConnectorsAppendix a Serial Cabling AppendicesSerial Computers Serial PrintersPin Signal Name Acronym Description Appendix B Pinout SpecificationsC36F DB25 Pin Signal Name Port Description Appendix C MP1000 Memory Board Verification of Installation Installing the BoardAdding Chips to an Empty Board or Adding Additional Chips Once CompletedAppendix E General Specifications Appendix D Factory DefaultsPage Stancliff Road Phone 281 Houston, Texas

CTP-8S specifications

The Rose Electronic CTP-8S is an advanced KVM (keyboard, video, mouse) switch designed to meet the demands of modern IT environments. This device allows users to control multiple computers from a single console, enhancing both efficiency and productivity. With its robust features and cutting-edge technologies, the CTP-8S stands out in the market of KVM solutions.

One of the key features of the CTP-8S is its ability to support multiple users. This KVM switch can handle up to eight different computer systems, providing seamless switching between them. This capability is particularly beneficial in environments like data centers, studios, and security operations, where rapid access to multiple devices is essential.

The CTP-8S employs advanced video technology, supporting resolutions up to 1920x1200 at 60Hz. This ensures that users can enjoy clear and sharp visuals, an essential aspect for tasks that require precise monitoring and analysis. The switch supports a variety of video interfaces, making it versatile for different setups, including HDMI, DVI, and VGA connections.

Another standout characteristic of the CTP-8S is its USB compatibility. The device allows users to connect standard USB keyboards and mice, ensuring compatibility with a wide range of peripherals. Furthermore, the CTP-8S supports USB 2.0 hubs, enabling users to connect additional devices such as flash drives and printers, enhancing productivity in multi-tasking environments.

The CTP-8S also features a user-friendly interface, with a straightforward switching mechanism that allows for quick and effortless transitions between computers. Users can switch between systems using hotkeys or the provided remote control, making the device exceptionally convenient to operate in dynamic settings.

In terms of reliability, the CTP-8S boasts a durable design built to withstand the rigors of continuous use. Its robust metal housing provides protection against physical damage, while advanced thermal management ensures optimal performance even during extended operation.

Overall, the Rose Electronic CTP-8S is an exceptional KVM switch that combines user-friendly features with advanced technologies to support complex IT needs. Its ability to manage multiple systems simultaneously, high-quality video output, and compatibility with various peripherals make it an ideal choice for businesses and professionals looking to optimize their workflow.