Rose electronic CTP-8S manual Maintenance and Repair, Technical Support

Page 29

Maintenance and Repair

The exterior surface of the unit may be wiped with a damp cloth to keep it clean. The unit does not contain any jumpers or serviceable parts inside. Opening the unit invalidates the warranty except in the case of an authorized memory upgrade or firmware updates. Any malfunction of the unit should be reported to a factory authorized repair center for service. Any discrepancies in the operation of the unit according to this manual should be reported to the Technical Support department of Rose Electronics.

Technical Support

If you cannot determine the nature of a problem, please call Rose Electronics and ask for Technical Support. If possible, call from a phone located near the unit--we may be able to solve your problem directly over the phone. If we cannot solve your problem, and determine that the fault is in the unit, we will issue a Return Authorization (RA) number which must appear on the outside of all returned products. The unit should be double- packed in the original container, insured, and shipped to the address given to you by our Technical Support representative.

To speak to a Technical Support representative, call (713) 933-7673 from 8:O0-Noon and 1:00-5:00 CST, Monday through Friday.

CARETAKER PLUS INSTALLATION AND OPERATIONS MANUAL

25

 

Image 29
Contents Installation Operations Manual Page Limited Warranty Table of Contents Introduction FeaturesDisclaimer First Steps Model Number and OptionsCaretaker Plus Front Panel Display Front Panel DisplaySerial Set-up For Other Computers or Terminals Mode LPT1+COM1Serial Set-Up for PCs Caretaker Plus Rear Panel Serial Model Caretaker Plus Rear Panel Parallel Model Mode LPT1,,PParallel Set-Up Cabling ConfigurationParallel Cabling Serial CablingDisabled EnabledElectronics None DTRProtocol Configuration Menu ItemsTimeout Form Feed Disable Operator SwitchesInitialization String KeepExit Advanced FeaturesHelp Main Menu Unidirectional X-on/X-offAllow Timeout On Busy Ports Reverse Channel Data TimeoutFilter Characters Return To Previous MenuConfiguration Commands =DTR/DSR Protocol CommandGrounding Parallel Enable Logic CommandInitialization String Command Normal Operation OperationsInitial State Buffer Characteristics Printer Initialization Signal Parallel Models OnlyUnit Software Reset Function ExplanationCopy CON COM1CR TimeoutChanging the Serial Baud Rate Initialization StringAdding More Memory Buffer Memory Sizing and Read/Write Test Power Up Initial DisplayProgram Checksum Test Data LED, Busy LED, and Error LED Front Panel SwitchesBuffer Overflow Error Display Serial Models Only Static Ram Read/Write TestFlow Control Display Mode Serial Models Only Troubleshooting TroubleshootingII. Nothing happens when sending data III. Garbled data received at shared devicePorts do not time out Technical Support Maintenance and RepairDiagnostic Modes DiagnosticsRestore To Factory Default Short TestSerial Units Print Configuration/Test Pattern FunctionParallel Units NoneLong Test Without Loopback Long Test with Loopback Loopback Test ConnectorsAppendix a Serial Cabling AppendicesSerial Computers Serial PrintersC36F DB25 Pin Signal Name Port Description Appendix B Pinout SpecificationsPin Signal Name Acronym Description Appendix C MP1000 Memory Board Verification of Installation Installing the BoardAdding Chips to an Empty Board or Adding Additional Chips Once CompletedAppendix E General Specifications Appendix D Factory DefaultsPage Stancliff Road Phone 281 Houston, Texas

CTP-8S specifications

The Rose Electronic CTP-8S is an advanced KVM (keyboard, video, mouse) switch designed to meet the demands of modern IT environments. This device allows users to control multiple computers from a single console, enhancing both efficiency and productivity. With its robust features and cutting-edge technologies, the CTP-8S stands out in the market of KVM solutions.

One of the key features of the CTP-8S is its ability to support multiple users. This KVM switch can handle up to eight different computer systems, providing seamless switching between them. This capability is particularly beneficial in environments like data centers, studios, and security operations, where rapid access to multiple devices is essential.

The CTP-8S employs advanced video technology, supporting resolutions up to 1920x1200 at 60Hz. This ensures that users can enjoy clear and sharp visuals, an essential aspect for tasks that require precise monitoring and analysis. The switch supports a variety of video interfaces, making it versatile for different setups, including HDMI, DVI, and VGA connections.

Another standout characteristic of the CTP-8S is its USB compatibility. The device allows users to connect standard USB keyboards and mice, ensuring compatibility with a wide range of peripherals. Furthermore, the CTP-8S supports USB 2.0 hubs, enabling users to connect additional devices such as flash drives and printers, enhancing productivity in multi-tasking environments.

The CTP-8S also features a user-friendly interface, with a straightforward switching mechanism that allows for quick and effortless transitions between computers. Users can switch between systems using hotkeys or the provided remote control, making the device exceptionally convenient to operate in dynamic settings.

In terms of reliability, the CTP-8S boasts a durable design built to withstand the rigors of continuous use. Its robust metal housing provides protection against physical damage, while advanced thermal management ensures optimal performance even during extended operation.

Overall, the Rose Electronic CTP-8S is an exceptional KVM switch that combines user-friendly features with advanced technologies to support complex IT needs. Its ability to manage multiple systems simultaneously, high-quality video output, and compatibility with various peripherals make it an ideal choice for businesses and professionals looking to optimize their workflow.