Toshiba IK-65WDA instruction manual White BAL White Balance, ID. = Camera ID

Page 19

(7) WHITE BAL (WHITE BALANCE)

Move the cursor to the position shown in fig.

 

 

 

Use the

SELECT switches to select

S H U T T E R

D / N : M I D

AUTO, MANUAL in the WHITE BAL settings.

WD R

O N

 

 

A L C

L E V : 0 0

AUTO : The white balance is automatically

B L C

A U T O

 

adjusted corresponding to the color

G A I N

S T D

 

temperature variations on the ob-

S H A R P N E S S M I D

 

WH I T E - B A L

A U T O

: 0 0

 

ject. The camera is applicable to a

 

 

 

 

 

color temperature range of 2500-

N E X T

 

 

 

10K. Press the SELECT switch to

 

 

 

E X I T C A N C E L D E F A U L T

 

enter AUTO set mode. Use the

 

 

 

 

 

SELECT switches to adjust the shift

 

 

 

 

value of the convergence point.

 

 

 

 

When data becomes big in the positive side, a convergence point is altered in

 

the red side. When data becomes big in the negative side, a convergence point is

 

altered in the blue side.

 

 

 

MANUAL : Press the SELECT switch to enter the MANUAL SETTINGS. Use the SELECT switches to adjust R Gain (Red) and B Gain (Blue) until the desired white balance is reached. Press SELECT to exit the manual settings.

INDOOR1 : Optimum setting for the white balance when the color temperature is 3000K indoors with an incandescent lamp.

INDOOR2 : Optimum setting for the white balance when the color temperature is 4000K indoors with a fluorescent lamp.

OUTDOOR : Optimum setting for the white balance when the color temperature is 5200K in an outside environment.

NOTES

If the optimum white balance cannot be obtained, then try to set AWB-RNG to WIDE. (Refer to 8.3 (11).)

(8) ID. = Camera ID.

Refer to 8.2 (6).

(9) ID. POS = Camera ID. Position

Refer to 8.2 (7).

19

Image 19
Contents IK-65WDA Important Safeguards Field Installation Marking Components Features & DescriptionIK-65WDA has the following functions Rear View Part Names & FunctionsConnections and Operations Basic connection for a single system configurationOperation Line-Lock ControlLens Back focus adjustmentWDR DIP3 ON/OFF LINE-LOCK PhaseDIP Switch Settings Iris DIP2 AES/DCDN DIP4 MID/S.DNx32 Menu Driven SET-UP RS422 setting menuMain menu Except for DIP3 and DIP4 on Advanced Main menu DIP3 and DIP4 on N = DAY/NIGHT function Setting switches and the functionsOn Screen Main menu Except for DIP3 and DIP4 on WDR = Wide dynamic range functionBLC = Back light compensation ID. = Camera ID Gain = AGC gain settingID. POS = Camera ID. Position Exit CancelDefault Default settingsShutter On Screen Advanced Main menu DIP3 and DIP4 onSharpness White BAL White Balance AWB-RNG = AWB control range PTN-GEN = Test pattern generatorDNR = Digital noise reduction HI-RESO = Hi resolutionNEXT, Back X T I T C a N C E L D E Fault U T T E R BIT-RATE On Screen RS422 setting menu for Remote ControlAddress ProtocolRx+ Tx+ Remote ControlDo not shoot intense light Install the camera Where no video noise appearsCheck the ambient temperature and humidity Do not aim the camera at the sunCondition Check Points Case of ProblemsINDOOR2, Outdoor SpecificationsExterior View Page Memo