Toshiba IK-TF9C instruction manual Menus, Shutter Electronic shutter, Flicker may be large, Trg

Page 12

7. 2 Menus

•Select the menu to change the setting by referring the item "7.1 Using the Menus".)

•When the [MENU UP], [MENU DOWN] buttons are pushed, the "→" on the screen moves up and down. Move the "→" to the item to change.

Note:

When performing the mode setting in the menu display while selecting ON in "PART" (refer to page 28) and E.TRG in "MODE", the display shows normal mode and then the camera returns the setting mode.

( 1 ) SHUTTER (Electronic shutter)

The electronic shutter has three modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger).

Set the "→" to "MODE" and push [DATA UP], [DATA DOWN] button to select the desired mode among "MANU", "SS", "E.TRG".

MANUAL

: It is possible to select the exposure time from eleven speed setting; OFF, 1/100s, 1/250s,

 

1/500s, 1/1000s, 1/2000s, 1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/100000s.

 

Note:

 

When setting a rapid shutter speed, sensitivity degrades according to the speed.

 

When a discharging light such as fluorescent lamp, etc. is used for the illumination,

 

the flicker may be large.

SS: Shutter speed can be set by the double horizontal scanning time (2H) unit or by the frame unit.

E.TRG

: Exposure is performed and images are output by external trigger. E.TRG includes the four

 

modes described below. (For details of specifications, refer to the item “7.4 E.TRG

 

(External trigger)”.)

•1P SNR (1 Pulse Sync Non Reset)

The charge begins to accumulate after the trigger pulse is received, and 1 frame images are output according to the internal vertical sync signal timing. The exposure/accumula- tion time can be set from 0.01 to 50 ms. The trigger signal timing can be set to either the rising or falling edge.

•1P SR (1 Pulse Sync Reset)

The charge begins to accumulate after the trigger pulse is received. Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output. The exposure/accumulation time can be set from 0.01 to 50 ms. The trigger signal timing can be set to either the rising or falling edge.

•PW SNR (Pulse width trigger Sync Non Reset)

The charge begins to accumulate after the trigger pulse is received, and 1 frame images are output according to the internal vertical sync signal timing. This is the mode to set the exposure period by the pulse width of the trigger. The trigger signal polarity can be set to either the positive or negative polarity.

•PW SR (Pulse width trigger Sync Reset)

The charge begins to accumulate after the trigger pulse is received. Upon completion of accumulation the vertical sync signal is reset and 1 frame images are output. This is the mode to set the exposure period by the pulse width of the trigger. The trigger signal polarity can be set to either the positive or negative polarity.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents For Customer Use Following information is only for EU-member statesSafety Precautions Avoid setting in humid, smoky, vaporized or dusty places DisclaimerTable of Contents Components Names and Functions Connector Pin Assignments ConnectionStandard Connection Operation White BalanceAutomatic White Balance Manual White Balance Result displayed Meaning Shutter speed mode is E.TRG mode Reasons. Such as no white area is included in an object, etcItems Controlled by Using on Screen Display Available selections Preset valueMode Setting by on Screen Display Using the MenusDisp TRG 1P SNR 1P SR TRG PW SNR TRG PW SRMenus Shutter Electronic shutterFlicker may be large TRGChanging each setting in Manu mode Partial scanning settingChanging the shutter speed Changing each setting in SS synchro. scan mode Mode = SSChanging the shutter speed setting Changing each setting in E.TRG mode Changing each setting in 1P SNR modeChanging the polarity of inputting trigger pulse setting Changing 1P SNR exposure time settingChanging each setting in 1P SR mode Mode = E.TRG E.TRG = 1P SRChanging 1P SR exposure time setting Changing each setting in PW SNR mode Mode = E.TRG E.TRG = PW SNRChanging each setting in PW SR mode Mode = E.TRG E.TRG = PW SRChanging each setting in Gain Changing the gain in Manu modeGain Video gain WHT BAL White balance MANU/OFF Changing gamma correctionChanging master pedestal Changing R pedestalSetting to factory setting status Changing the shading correction modeChanging the manual shading correction setting OptionSetting by the frame Setting by 2HSynchro. Scan Operation Fval Lval Davl1P SNR 1 Pulse Trigger Sync Non Reset 1 Pulse Trigger SYNC-NON Reset Picture Output TimingE. TRG External trigger Fval Lval Dval1P SR 1 Pulse Trigger Sync Reset 1 Pulse Trigger SYNC-RESET Picture Output TimingPW SNR Pulse width trigger SYNC-NON Reset Pulse Width Trigger SYNC-NON Reset Picture Output TimingPW SR Pulse width trigger SYNC-RESET 1 Pulse Width Trigger SYNC-RESET Picture Output TimingWhen Partial Scanning Mode is on Partial ReadPartial Scanning OFF All pixels scanning Partial Scanning onOutput Waveform Timing Chart Horizontal Output Waveform Timing ChartVertical Output Waveform Timing Chart Fval LVAL、 DvalSpecifications RGB, 3CCDExternal Appearance Diagram Before Making a Service CallSymptom Items to be checked Limited One 1 Year Warranty of Labor and Parts Step-by-step Procedures How to Obtain Warranty ServiceImaging Systems Division
Top Page Image Contents