Miller Camera Support DS20, DS10 manual Operating Instructions, Fluid Head Set-up, Camera Set-up

Page 4

Operating Instructions

Before using please read the following operating instructions. Do not omit any step. N.B. The safe operation of this piece of professional equipment is the responsibility of the operator.

1.Fluid Head Set-up

1.1Loosen the PAN HANDLE CLAMP fully, then rotate the PAN HANDLE until it is approximately perpendicular to the THREADED STUD and tighten the PAN HANDLE CLAMP - avoid contact wear between the serrations on the Fluid Head and the PAN HANDLE CLAMP, if this occurs then unwind the PAN HANDLE CLAMP further.

1.2Ensure that the TRIPOD BOWL is approximately horizontal. Place the Fluid Head into the TRIPOD BOWL, adjust the BUBBLE LEVEL such that the bubble is inside the black circle and tighten the CLAMP NUT.

1.4Note: If adjusting the level with your camera mounted, first ensure the camera is securely held before loosening

CLAMP NUT.

2.Camera Set-up

Please note that the best camera control can be achieved by balancing camera centre of gravity (C of G) over centre axis of the head, and by selecting the appropriate counterbalance position to suit the weight of the camcorder payload.

The DS5/DS10/DS20 is equipped with a sliding camera plate and a removable 1/4”-pin carriage which is standard mounting for DV and MiniDV camcorders. The DS20 is also fitted with a 3/8” &

41/4” screws which is standard mounting for DVCAM (see Fig1.3).

The 3/8” & 1/4” screws also allow the DS20 to attach to a proprietary Quick Release Tripod Adaptor or “tripod base plate” such as the Sony VCT-14 or Panasonic SHAN-TM700.

2.1Lock PAN and TILT LOCKS (rotate both levers clockwise until firm).

2.2Remove CAMERA PLATE from CAMERA PLATFORM by unlocking the SLIDE LOCK, pushing SAFETY TAB and sliding the CAMERA PLATE rearward

2.3With accessories and battery fitted to the camera, it is recommended to estimate the camera’s Centre of Gravity (C of G) for the purpose of correctly positioning the camera on the CAMERA PLATE. The camera’s C of G can be estimated by placing the camera on to a round rod and then shifting it backwards or forwards until a balance point – C of G - is achieved. It is recommended to identify this point as it will be useful in step 2.5.

2.4Refer to the Camera’s owners manual for correct method of attachment to the CAMERA PLATE. Attach the camera or the Quick Release Tripod Adaptor to the CAMERA PLATE and securely tighten the screws.

2.5Check that the SLIDE LOCK is loose, then align the CAMERA PLATE with the CAMERA PLATFORM and slide it forward until the safety mechanism is engaged. Then, slide the CAMERA PLATE so that the camera’s C of G

is directly above the centre axis of the Fluid Head and tighten the SLIDE LOCK. If this can not be achieved then reposition the camera or the Quick Release Tripod Adaptor on the SLIDING PLATE – step 2.4. This will ensure that the system has maximum stability.

Page 3 Page 5
Image 4
Page 3 Page 5
Contents DS5/DS10/DS20 Fluid Head Operator’s Manual Features and Controls Introduction Handle MountingOperating Instructions Fluid Head Set-upCamera Set-up 4 screws which is standard mounting for Dvcam see Fig1.3Is partially applied TIP Fine tuning can be achieved By adjusting the SlidingPlatform see step Cleaning MaintenanceOperating Instructions Pan / Tilt Drag Control StorageTechnical Data Up to 2.5 5.0 5.55.0 5.5 10.0 11.0 Camera Platform Type 40˚/+65˚ -40˚ / +149˚Miller sales or service centre #490#489 Pin carriage #493 Camera Screw 1/4

DS10, DS20, DS5, DS10, DS20 specifications

Miller Camera Support offers a renowned range of camera tripods, pivotal for modern cinematography, with notable models including the DS5, DS10, and DS20. Each of these tripods is designed to meet the dynamic needs of film and television production, providing stability, versatility, and precision in various shooting environments.

The Miller DS5 is an entry-level tripod that impresses with its robust build and lightweight design. It features a 5-position counterbalance system, allowing users to achieve the perfect balance for their camera setup. This adaptability is essential for operators working with different camera weights and sizes. The DS5 is also equipped with a fluid drag system for both pan and tilt movements, ensuring smooth and controlled motion during filming. Its high-quality aluminum construction guarantees durability while maintaining a manageable weight for easy transport.

Moving up the line, the DS10 offers enhanced capabilities for mid-range productions. This model boasts a higher payload capacity, accommodating heavier camera rigs without compromising stability. The DS10 features an advanced 7-step counterbalance system, which provides precise control over camera tilt. Its fluid drag system allows for fine adjustments in motion, ensuring professional-grade videography. Additionally, this tripod incorporates a quick-release plate that simplifies the camera setup process, saving valuable time on set.

The DS20 represents the pinnacle of Miller's tripod offerings, designed for the most demanding cinematic applications. This robust tripod is constructed from high-quality materials, capable of supporting large camera payloads and accessories. The DS20 features an advanced 8-step counterbalance system that allows for optimal adjustment based on the camera weight and configuration. This model also includes a superior fluid drag system, providing exceptional control for intricate shots. Its durable design ensures reliability even in challenging environments, making it a favorite among professional cinematographers.

All Miller tripods come equipped with intuitive features like a bubble level and adjustable rubber feet for added stability on uneven surfaces. The interchangeable camera plate designs across models enhance versatility, while the lightweight construction facilitates mobility. With their commitment to innovation and performance, the Miller DS range continues to set the standard for camera support solutions in the film industry.
Top Page Image Contents