Argus Camera RW-1 manual Display Messages, Error

Page 83

REFERENCE

Display Messages

ERROR

This message appears in the rare case that an im-

 

age is so complex that its file cannot be compressed

 

to the maximum allowable size.

 

 

NOT AVAILABLE

The displayed image was recorded on another type

FOR THIS IMAGE

of camera and cannot be enlarged.

 

 

CARD IS WRITE-

The LOCK switch on the SD memory card is in the

PROTECTED

locked position, so the card cannot be accessed in

SLIDE THE LOCK-SW the REC mode.

 

 

COPY ERROR

Amount of memory available on the memory card is

NOT ENOUGH

less than the data being copied to it.

MEMORY IN CARD

 

 

 

REPLACE BATTERY!

Battery power is low.

 

 

NOT AVAILABLE

You are trying to configure DPOF settings for cam-

FOR INTERNAL

era memory. DPOF settings can be configured for

MEMORY

the memory card only (Page 58).

 

 

CARD ERROR

Some problem occurred with the memory card or

PRESS MENU TO

built-in memory. Perform the following steps to cor-

FORMAT

rect it.

or

IMPORTANT!

INTERNAL MEMORY

ERROR

Performing this procedure deletes all files on the

PRESS MENU TO

memory card or built-in memory. Before

FORMAT

proceeding, try transferring recoverable files to a

 

computer or some other storage device.

1. Press MENU.

2. Use [ ] and [ ] to select “YES” and then press the

 

shutter release button.

 

If you want to cancel the procedure, press MENU

 

without selecting “YES”.

 

Before starting a format operation, connect the

 

AC adaptor for power or load a full set of fresh set

 

of alkaline or lithium batteries. Power interruption

 

during the format operation can result in im-

 

proper formatting, and even damage the memory

 

card or built-in memory and make it unusable.

 

The message “NO IMAGE” appears on the moni-

 

tor screen after the format operation is complete.

 

This indicates that the format operation was com-

 

pleted successfully.

 

 

MEMORY FULL

No more images can be stored under the current

CHANGE QUALITY/

image quality and size settings, but further record-

SIZE OR DELETE

ing is possible with different settings. Change the

 

image quality and size settings (page 39), or delete

 

images you no longer need (page 51).

 

 

MEMORY FULL

Memory is full. If you want to record more images,

DELETE UNNEEDED

delete images you no longer need (page 51).

IMAGES

This message also appears after data is trans-

 

ferred to a memory card from a computer when a

 

DCIM folder or other required files (page 72) can-

 

not be created because there is not enough

 

memory card space. Use your computer to free up

 

space by deleting files you no longer need. You

 

can press MENU to format the memory card, but

 

doing so deletes all data stored on the card.

 

83

¥¼©R¦W-10

Page 83

2002/6/18, AM 11:46Adobe PageMaker 6.5C/Win

Image 83
Contents Users Guide Unpacking IntroductionContents Playback Reference Features Precautions General PrecautionsOperating conditions Data Error PrecautionsAbout the camera’s backlight Lens PrecautionsCondensation FCC Warning General Guide Getting AcquaintedFront Back Bottom SideMonitor Screen Indicators REC modeIndicator Lamps Play modeAttaching the Strap Using the Soft CasePower Requirements Arrow Loading BatteriesGetting Acquainted Cell batteries with this camera Battery Handling PrecautionsLow Battery Indicator Using AC Power Turning the Camera On and Off Setting the Current Date and Time Power Save SettingsCursor Setting the Date and TimeExample October 18 Recording a Simple Snapshot Recording ImagesCompose the image on the monitor screen Recording Precautions About the REC Mode Monitor ScreenUsing Zoom Using the Flash Precautions when Using Flash Flash Status IndicatorsRecording Images Recording Macro Images Recording Consecutive Images Continuous Shutter Mode Using the Optical ViewfinderPress Menu or select Exit and then press SET Using the Self-Timer Setting the Maximum Number of ShotsCompose the image and then press the shutter release button Specifying Image Size and Quality To specify the image sizeTo specify the image quality Exposure Compensation Size/Quality Setting and Image CapacityPress Menu or select Exit and then press SET Checking an Image You Just Recorded Selecting White BalanceUsing a Memory Card To remove a memory card from the camera To insert a memory card into the cameraTo format a memory card Memory Card Precautions To copy flash memory images to a memory card Zooming the Displayed Image PlaybackBasic Playback Operation Using the Slide Show Feature Playback Deleting a Single Image Deleting ImagesTo exit the image delete procedure, press Menu SET Deleting All Unprotected ImagesFolders and Files Managing ImagesFolders Protecting Images Against Deletion FilesTo protect or unprotect a single image To exit the image protect procedure, press Menu To protect or unprotect all images Dpof To print selected imagesO e x i t t h e p r i n t To print all images Print Image Matching Changing the Display Language Other SettingsTurning the Monitor Screen Indicators On and Off Turning the Confirmation Tone On and Off Select the setting you want and then press SET Selecting the USB ModePC Camera Connecting to External Equipment Connecting to External EquipmentConnecting to a Television Selecting the Video Output Signal ModeTransferring Images to a Computer USB ConnectionConnecting the USB Cable Using a Memory Card to Transfer Image Data Disconnecting the USB CableDCF Protocol Memory Card DataImage Files Supported by the Camera Memory Card File StructurePrecautions when Using a Memory Card on a Computer To connect the camera as a PC camera Using the PC Camera ModeOther Requirements PC Camera Mode PrecautionsConnecting to Your Computer Camera Menus ReferenceIndicator Lamp Reference Reference Play mode Troubleshooting Reference Finder Display Messages ErrorMemory for Specifications Seconds, 2 seconds Reference Software Driver Installation Guide Install USB driver for Mac Loading Image by USB Cable By Software from Photo Suite