TANDBERG 880, 990, 770 user manual Alert Tones & Volume, Restore Audio Defaults

Page 61

TANDBERG Videoconferencing System

Advanced use

The echo canceller tries to estimate the echo path from the speaker system to the microphones. Moving objects change this path, therefore try to avoid moving objects. Be especially aware of large objects and objects placed close to either the microphone or the speaker system as these objects will cause severe changes to the echo path.

Avoid putting paper sheets etc. on the microphone.

Avoid moving the microphone or loudspeaker.

In the event of poor echo cancelling, allow the canceller to adapt. After each change, the echo canceller requires a few seconds to adapt. Do not change the settings without allowing the echo canceller to adapt to the new audio environment.

In the presence of low frequency noise, enable the noise reduction (NR).

Alert Tones & Volume

To help distinguish between incoming video calls and ordinary telephone calls, different ringing tones may be selected. You may also select different volume levels for the ringing tone.

Alert Speaker

The system also has an internal, call alerting speaker.

On: The internal speaker will warn you of an incoming call even though the monitor may not be switched on.

Key Tones

The Key Tones may be switched on and off.

Restore Audio Defaults

There are many audio settings and the codec could easily be made unusable by configuring these by mistake. It is therefore possible to return all audio settings to their factory default settings by using Restore Audio Defaults.

61

Image 61
Contents 990 / 880 Tandberg Videoconferencing System Trademarks and copyright Environmental IssuesOperator Safety Summary Contents Peripheral Equipment Advanced useAppendices Index 108 TIP IntroductionLAN Menu structureTandberg Videoconferencing System Camera Remote controlCodec Table microphonePrecautions InstallationUnpacking Microphone cable Connecting cablesMonitor cables 5b. Wireless LAN Insert PC Card Power cableIsdn cables 5a. LAN cableSelect Audio/Video input on monitor Power onMenu System configurationLAN configuration Isdn configurationSystem start-up Getting startedWelcome menu Basics Making a call Making and ending callsTIP Selecting / setting default quality bandwidth Selecting / setting default network End a call Answer a callCorrecting keying mistakes Press D Irectory to bring up the following menu DirectoryEdit Entry Add New EntryDelete Entry Add Site Add MultiSite EntryGeneral use Adjusting volumeView outgoing video selfview Microphone on/offOn Screen Symbols Do Not Disturb / Sleep ModeControlling the Main Camera Focusing cameraSelecting video sources Moving / zooming cameraVoice Activated Camera Positioning Selecting presets PresetsStoring presets Far end camera control Fecc Sending a snapshot Sending and receiving snapshotsViewing a snapshot Receiving a snapshotAdd Duo Video Duo VideoEnd a Duo Video call MultiSite MCU MultiSite cascading Establishing MultiSite meetings using DirectoryAdding an extra site dial out Adding an extra site dial Disconnecting sites from a conferencePC SoftPresenter PC PresenterText Chat / Closed Captioning Web-interfaceStreaming Other PC applicationsSnapshots Advanced use Menu PasswordMain menu Call quality Qcif Advanced call qualityDuo Video Mode Presentation ModePresentations Duo Video QualityDuo Video / Snapshot Source Duo Video NumberAuto-Display Snapshot Snapshot FilterAutoanswer UtilitiesFar end camera control Dual MonitorWelcome Menu Auto-PIPContinuous Presence MCU status lineWeb Snapshots MCU services Quick Menu Release floor Request floorTerminal Names View site #Chair control Audio Inputs Audio SettingsLevel Settings Audio Outputs Echo Control Page Automatic Gain Control AGC Settings Restore Audio Defaults Alert Tones & VolumeCamera Tracking Mode Video SettingsDocument Camera Brightness FocusWhitebalance Video NameVGA Settings VNC Settings Network Configuration Terminal SettingsISDN-BRI Settings Page Spids This Service has Limited Access on Some Isdn Networks Parallel dial LAN Settings Page Settings Page Rsvp Advanced H.323 SettingsQoS Type IP Type of Service TOSIP Precedence DiffservIP Settings Page Wireless LAN Settings Increased Encryption Level will Decrease Performance Snmp Settings Access Code Call SettingsIncoming MCU calls Incoming telephone callsEncryption Secure Conference Encryption ModeNetwork Profiles Max Call LengthDataport configuration Page Software Options LanguageSystem info DiagnosticsChannel status TIP Call status Test subsystem Restore defaults View current settingsIP Address Conflict Check Interfaces Peripheral EquipmentPage Dual Monitor Tracker Document cameraVCR Playback Video Cassette Recorder VCRVCR Recording Additional microphones Extra fixed camerasTandberg AppendicesUsing Telesync TS-256 SW56/ISDN adapter Appendix 2 Connecting the system to the Switched 56 networkAppendix 3 Environmental considerations Loudspeaker volumeIris control and lighting BackgroundHow to prepare a typical room for videoconferencing Guidelines for setting up videoconferencing roomsAppendix 4 Using the file system Custom logos · Go to the folder where your logo is located ABC Appendix 5 Security106 107 Appendix 6 Declaration of Conformity Index Index Tandberg Videoconferencing System Current settings 91 outgoing video 27 Viewing a still image
Related manuals
Manual 3 pages 53.31 Kb