AGFA DC-733i manual Inserting the Batteries, Low Battery Indicator, About Battery Type

Page 10

Inserting the Batteries

The camera is powered by two AA-size alkaline batteries or rechargeable NiMH (min. 2500 mAh / 1.2V) batteries.

1 Open the battery cover.

ySlide the battery cover in the direction indicated by the arrow.

2 Insert the batteries.

yInsert two AA-size batteries with the positive (+) and negative (-) poles matching the directions indicated inside the battery room.

3 Close the battery cover.

Low Battery Indicator

A low battery indicator appears on the LCD screen when the batteries are nearly exhausted. Batteries should be replaced promptly when the low battery indicator appears.

Caution

yRisk of explosion if battery is replaced by an incorrect type dispose of used batteries according to the instructions.

yBe sure to turn off the camera power before insert or remove batteries.

yUse only Alkaline or NiMH battery to power this camera. Use of any other type battery is not recommended.

yReplace all batteries at the same time. Never mix old and new batteries.

yRemove batteries if you will not be using them for a long time.

yThe camera body may feel warm after extended use. This is normal.

About Battery Type

After replacing the batteries, please check the Battery Type in the setup menu ( page 18).

5

Image 10

Contents Page Using your batteries Extending battery lifePrecautions „ FCC Compliance and AdvisoryContents IiiMaking Connections Using This Menu Getting StartedScope of delivery Attaching the Hand StrapParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Tips Inserting the Memory CardInsert the card About Camera MemorySelect a language Setting the Display Language / Date & TimeSetting the Display Language Press the Menu button to close the menuApply the setting Setting the Date & TimeSet date and time Using the LCD Monitor REC modePlay mode Dpof„ Play mode „ REC modeChanging the LCD Status Power Saving Function Turning the Power On and OffBasic Operation Selecting the REC mode Changing the ModeSwitching between REC mode and Play mode Set the camera to the REC mode Launch the mode palettePage REC menu Using the MenusChange the setting Select an itemREC menu list Movie Setup menuOpen the Setup menu Press the Menu n button to close the menuReset Setup menu listVolume ShutterComputer / Printer NtscPAL AlkalineHalf press the shutter button to focus the image Basic RecordingRecording Still Images Take a pictureUsing the Q mode Resolution Values Setting the Resolution and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Double Using the Self-timer & Burst10 sec BurstSetting the Movie Size Recording Movie ClipsPlaying Back Audio Clips Recording Audio ClipsPress the shutter button again to end recording Press the SET button to start recording for 30 seconds Recording a Voice MemoOpen the Play menu Playing Back a Voice MemoSetting the White Balance Setting the MeteringOther Recording Functions Setting the AEB Setting the ISOSetting the Exposure Setting the HighlightSetting the Photo Effect Setting the SharpnessSetting Date Stamp Playing Back Images Turn the power on, and set the camera to the Play modePlayback Press the four-way controlTrim the image Magnifying & Trimming Still ImagesMagnify the image Save the imagePlaying a Slide Show Change the slide show settingsViewing in Thumbnail Playing the slide showDeleting Files Deleting a Single FileDeleting Multiple Files Deleting All FilesProtecting All Files Press the SET button to delete all unprotected imagesProtecting a Single File Press or to select Lock all, and then press the SET buttonPress To select Select, and then press the SET button Protecting Multiple FilesProtect images Press the SET button to rotate the image Editing ImagesRotating Still Images Changing the Image SizePress or to select Single, then press the SET button Copying the FilesChanging the Image with Effects Press or to select the image you want to copy to a cardSetting the Dpof Print the date stamp outChoosing a Startup Image Making Connections Connecting the Camera to a TVSet the TV input signal to Video Turn off the camera and the TVUsing the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Software Installation System RequirementsInstall VideoStudio 7 SE VCD Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Utilities DriversSetup language and click OK Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Follow the on-screen instructions to install the driversUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic Folder Structure AppendixAbout the Folder & File Name File NamingTroubleshooting Problem Cause SolutionMode Still Capture Function Function Available ListAEB Specifications Ntsc / PALOnline Service Service & Support Hotline GermanyManufactured by plawa-feinwerktechnik GmbH & Co. KG Declaration of Conformity