AGFA DC-733i manual Troubleshooting, Problem Cause Solution

Page 55

Troubleshooting

Problem	Cause	Solution
Power does not turn on.	Battery is inserted in the	Reload battery in the correct
	wrong direction.	direction.

	Batteries are dead.	Replace or recharge batteries.

	The battery compartment	Make sure the battery
	door is open.	compartment door is securely
		closed.

The camera does not take	The flash is charging.	Wait for the flash to charge.
pictures.
pictures.	Memory is full.	Insert a new memory card.

	Memory card is not	The card may be defective,
	formatted correctly.	use a new card.

Image is not recorded when	The Flash is charge.	Wait for the flash to charge.
the shutter button is
the shutter button is	Memory is full.	Insert a new memory card.
pressed.

The flash does not fire	Flash is set to OFF.	Set the flash to any mode
		except off.

Image is blurry or out of	The camera was moving	Hold the camera steady when
focus.	when the image was	shooting picture.
	captured.

	The subject was beyond	Turn the Macro mode on it the
	the range within which the	subject is within 15 cm (zoom
	camera can focus.	out) or 40 cm (zoom in).
		Do not use Macro mode when
		shooting distant subjects.

Image is not displayed on	A memory card with	This camera cannot display
the LCD monitor.	non-DCIF images (recorded	non-DCIF images.
	with other camera) is
	loaded.

Recorded images are not	The camera was turned	If the battery low indicator
saved in memory.	off/powered down before	appears on the LCD monitor,
	the image was stored in	replace the battery
	memory	immediately.

Cannot transfer images to a	USB driver is not installed.	Install the USB driver before
computer after connecting		you connect the camera to a
the USB cable.		computer / turn the camera
		on.

50

Image 55

Contents Page Extending battery life Using your batteries„ FCC Compliance and Advisory PrecautionsIii ContentsMaking Connections Getting Started Using This MenuAttaching the Hand Strap Scope of deliveryParts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries About Camera Memory Inserting the Memory CardInsert the card TipsPress the Menu button to close the menu Setting the Display Language / Date & TimeSetting the Display Language Select a languageApply the setting Setting the Date & TimeSet date and time REC mode Using the LCD MonitorDpof Play mode„ Play mode „ REC modeChanging the LCD Status Power Saving Function Turning the Power On and OffBasic Operation Set the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Play mode Selecting the REC modePage Select an item Using the MenusChange the setting REC menuPress the Menu n button to close the menu Setup menuOpen the Setup menu REC menu list MovieShutter Setup menu listVolume ResetAlkaline NtscPAL Computer / PrinterTake a picture Basic RecordingRecording Still Images Half press the shutter button to focus the imageUsing the Q mode Resolution Values Setting the Resolution and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Burst Using the Self-timer & Burst10 sec DoubleRecording Movie Clips Setting the Movie SizePlaying Back Audio Clips Recording Audio ClipsPress the shutter button again to end recording Playing Back a Voice Memo Recording a Voice MemoOpen the Play menu Press the SET button to start recording for 30 secondsSetting the White Balance Setting the MeteringOther Recording Functions Setting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting the Photo Effect Setting the SharpnessSetting Date Stamp Press the four-way control Turn the power on, and set the camera to the Play modePlayback Playing Back ImagesSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying the slide show Change the slide show settingsViewing in Thumbnail Playing a Slide ShowDeleting a Single File Deleting FilesDeleting All Files Deleting Multiple FilesPress or to select Lock all, and then press the SET button Press the SET button to delete all unprotected imagesProtecting a Single File Protecting All FilesPress To select Select, and then press the SET button Protecting Multiple FilesProtect images Changing the Image Size Editing ImagesRotating Still Images Press the SET button to rotate the imagePress or to select the image you want to copy to a card Copying the FilesChanging the Image with Effects Press or to select Single, then press the SET buttonPrint the date stamp out Setting the DpofChoosing a Startup Image Turn off the camera and the TV Connecting the Camera to a TVSet the TV input signal to Video Making ConnectionsUsing the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable System Requirements Software InstallationUtilities Drivers Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Install VideoStudio 7 SE VCDFollow the on-screen instructions to install the drivers Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Setup language and click OKUsing the Software Installing VideoStudio 7 SE VCDUlead Photo Explorer 8 SE Basic File Naming AppendixAbout the Folder & File Name Folder StructureProblem Cause Solution TroubleshootingFunction Available List Mode Still Capture FunctionAEB Ntsc / PAL SpecificationsOnline Service Service & Support Hotline GermanyManufactured by plawa-feinwerktechnik GmbH & Co. KG Declaration of Conformity