AGFA DC-733i manual Precautions, „ FCC Compliance and Advisory

Page 3

Precautions

Before using the camera, please ensure that you read and understand the safety precautions described below. Always ensure that the camera is operated correctly.

yDo not aim the camera directly into the sun or other intense light sources which could damage your eyesight.

yDo not try to open the case of the camera or attempt to modify this camera in any way. High-voltage internal components create the risk of electric shock when exposed. Maintenance and repairs should be carried out only by authorized service providers.

yDo not fire the flash too close to the eyes of animals or people, especially for young children. Eye damage may result. In particular, remain at least one meter away from infants when using flash.

yKeep the camera away from water and other liquids. Do not use the camera with wet hands. Never use the camera in the rain or snow. Moisture creates the danger of fire and electric shock.

yKeep the camera and its accessories out of the reach of children and animals to prevent accidents or damage to the camera.

yIf you notice smoke or a strange odor coming from the camera, turn the power off immediately. Take the camera to the nearest authorized service center for repair. Never attempt to repair the camera on your own.

yUse only the recommended power accessories. Use of power sources not expressly recommended for this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards.

„FCC Compliance and Advisory

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) this device may not cause harmful interference, and 2.) this device must accept any interference received, including interference that may cause unsatisfactory operation.

This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment to an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. When shielded interface cables have been provided with the product or when specified additional components or accessories have elsewhere been designated to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations.

ii

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Page Extending battery life Using your batteries„ FCC Compliance and Advisory PrecautionsIii ContentsMaking Connections Getting Started Using This MenuAttaching the Hand Strap Scope of deliveryParts of the Camera Page Low Battery Indicator About Battery TypeInserting the Batteries About Camera Memory Inserting the Memory CardInsert the card TipsPress the Menu button to close the menu Setting the Display Language / Date & TimeSetting the Display Language Select a languageSetting the Date & Time Apply the settingSet date and time REC mode Using the LCD MonitorDpof Play mode„ REC mode „ Play modeChanging the LCD Status Turning the Power On and Off Power Saving FunctionBasic Operation Set the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Play mode Selecting the REC modePage Select an item Using the MenusChange the setting REC menuPress the Menu n button to close the menu Setup menuOpen the Setup menu REC menu list MovieShutter Setup menu listVolume ResetAlkaline NtscPAL Computer / PrinterTake a picture Basic RecordingRecording Still Images Half press the shutter button to focus the imageUsing the Q mode Setting the Resolution and Quality Resolution ValuesQuality Values Using the Zoom Function Using the Flash Using the Macro Burst Using the Self-timer & Burst10 sec DoubleRecording Movie Clips Setting the Movie SizeRecording Audio Clips Playing Back Audio ClipsPress the shutter button again to end recording Playing Back a Voice Memo Recording a Voice MemoOpen the Play menu Press the SET button to start recording for 30 secondsSetting the Metering Setting the White BalanceOther Recording Functions Setting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting the Sharpness Setting the Photo EffectSetting Date Stamp Press the four-way control Turn the power on, and set the camera to the Play modePlayback Playing Back ImagesSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying the slide show Change the slide show settingsViewing in Thumbnail Playing a Slide ShowDeleting a Single File Deleting FilesDeleting All Files Deleting Multiple FilesPress or to select Lock all, and then press the SET button Press the SET button to delete all unprotected imagesProtecting a Single File Protecting All FilesProtecting Multiple Files Press To select Select, and then press the SET buttonProtect images Changing the Image Size Editing ImagesRotating Still Images Press the SET button to rotate the imagePress or to select the image you want to copy to a card Copying the FilesChanging the Image with Effects Press or to select Single, then press the SET buttonPrint the date stamp out Setting the DpofChoosing a Startup Image Turn off the camera and the TV Connecting the Camera to a TVSet the TV input signal to Video Making ConnectionsConnecting the Camera to a PC Using the Card ReaderConnecting the Camera to a Computer with the USB Cable System Requirements Software InstallationUtilities Drivers Installing the SoftwareInstall Ulead Photo Explorer 8 SE Basic Install VideoStudio 7 SE VCDFollow the on-screen instructions to install the drivers Installing the Software DriverInstalling Ulead Photo Explorer 8 SE Basic Setup language and click OKInstalling VideoStudio 7 SE VCD Using the SoftwareUlead Photo Explorer 8 SE Basic File Naming AppendixAbout the Folder & File Name Folder StructureProblem Cause Solution TroubleshootingFunction Available List Mode Still Capture FunctionAEB Ntsc / PAL SpecificationsService & Support Hotline Germany Online ServiceManufactured by plawa-feinwerktechnik GmbH & Co. KG Declaration of Conformity
Top Page Image Contents