AGFA DC-630i manual Iii, FCC Compliance and Advisory

Page 4

FCC Compliance and Advisory

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.) this device may not cause harmful interference, and 2.) this device must accept any interference received, including interference that may cause unsatisfactory operation.

This equipment has been tested and found to comply with the limits for a Class B peripheral, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

yReorient or relocate the receiving antenna.

yIncrease the separation between the equipment and receiver.

yConnect the equipment to an outlet on a circuit different from that to which the receiver is connected.

yConsult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. When shielded interface cables have been provided with the product or when specified additional components or accessories have elsewhere been designated to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations.

iii

Image 4

Contents Page Extending battery life DisclaimerPrecautions Iii „ FCC Compliance and AdvisoryContents Making Connections Using This Menu Getting StartedAttaching the Wrist Strap Parts of the Camera Page About Battery Type Low Battery IndicatorInserting the Batteries Inserting the Memory Card Insert the cardTips About Camera MemorySetting the Display Language / Date & Time Setting the Display LanguageSelect a language Press the Menu button to close the menuApply the setting Setting the Date & TimeSet date and time Using the LCD Monitor REC modePlayback mode Dpof„ Playback mode „ REC modeChanging the LCD Status Turning the Power On and Off Press the Power button n again to turn the power offPower Saving Function Basic OperationChanging the Mode Switching between REC mode and Playback modeSelecting the REC mode Set the camera to the REC mode Launch the mode paletteSelecting the ASM mode Set the camera to the REC modeLaunch the ASM mode Exit the ASM modeUsing the Menus Change the settingREC menu Select an itemOpen the Setup menu Setup menuREC menu list Movie Press the Menu n button to close the menu Setup menu list ResetBeep OffNtsc PALComputer / Printer AlkalineBasic Recording Recording Still ImagesHalf press the shutter button to focus the image Take a pictureStabilizer Off / On Using the Q modeFace Tracking Off / On Resolution Values Setting Image Size and QualityQuality Values Using the Zoom Function Using the Flash Using the Macro Using the Self-timer & Burst 10 secDouble BurstTurn the power on, and set the camera to Using the Aperture PriorityUsing the Shutter Priority Using the Manual Exposure Setting the Movie Size Recording Movie ClipsStart recording Finish recordingPress the shutter button again to end recording Recording Audio ClipsPlaying Back Audio Clips Recording a Voice Memo Open the Playback menuPress the SET button to start recording for 30 seconds Playing Back a Voice MemoSetting the White Balance Setting the MeteringOther Recording Functions Setting the ISO Setting the ExposureSetting the AEB Setting the HighlightSetting the Photo Effect Setting the SharpnessSetting Date Stamp Setting Face tracking Setting StabilizerSetting Photo Frame Turn the power on, and set the camera to the Playback mode PlaybackPlaying Back Images Press the four-way control or nMagnifying & Trimming Still Images Magnify the imageTrim the image Save the imageChange the slide show settings Viewing in ThumbnailButton to show the selected image in full screen Playing a Slide ShowDeleting Files Deleting a Single FileDeleting Multiple Files Deleting All FilesProtecting a Single File Protecting All FilesOr to select Lock all, and then press the SET button Press the SET button to protect all imagesProtecting Multiple Files Protect imagesEditing Images Rotating Still ImagesPress the SET button to rotate the image Changing the Image SizeChanging the Image with Effects Choosing the Image with Photo FrameCopying the Files Or to select Single, then press the SET button Setting the DpofPrint the date stamp out Choosing a Startup Image Making Connections Connecting the Camera to a TVDisplay on TV Using the Card Reader Connecting the Camera to a PCConnecting the Camera to a Computer with the USB Cable Software Installation System RequirementsInstalling the Software Install Ulead Photo Explorer 8 SE BasicInstall VideoStudio 7 SE VCD Utilities DriversInstalling Ulead Photo Explorer 8 SE Basic Installing the Software DriverInstalling VideoStudio 7 SE VCD Using the Software Ulead Photo Explorer 8 SE BasicAppendix About the Folder & File NameFolder Structure File NamingTroubleshooting Problem Cause SolutionSpecifications Ntsc / PALFunction Available List ModeCapture 0EV AEB Factory Print Setting Using the PictBridgeSelect Images Resetting to Default Settings Starting PrintCustomer care Declaration of Conformity