Madrigal Imaging AVP2 owner manual Quick Start For CD

Page 13

A Quick Start For CD

There is a reasonable chance that either your CD transport or your DVD player may have a different set of output connectors than what we have assumed it might have in the “quickest start” section. In that case, setting up the AVP2 to take advantage of your particular equipment is still quite simple, though it will require a couple extra steps.

1MAKE THE PHYSICAL CONNECTIONS; TURN EVERYTHING ON

Connect the outputs of the AVP2 to your power amplifier(s), as indicated (front, rear, center, sub); connect a CD transport to any matching digital in- put connector on the AVP2, noting which connector you use; ensure that the main video output of the AVP2 is connected to your television (so you can see the on screen menus). Once this is done, turn on all the compo- nents involved (CD transport, AVP2, television, amplifiers). Turn the amps on last (always a good habit with any audio system).

2PRESS AND HOLD THE CD BUTTON ON THE FRONT OF THE AVP2

This shortcut of pressing and holding an input button will take you directly to the define button menu for that button.

3TELL THE AVP2 WHICH CONNECTOR YOU USED FOR YOUR CD

TRANSPORT IN STEP 1

13

We have no way of knowing what sort of digital interface your particular CD transport might use (AES/EBU? RCA? BNC? EIA-J?), but logically, you’d like to be able to use your main CD transport with the button labeled cd. This step allows you to use whatever connector you need to use in conjunction with the button you’d like to use.

Using the volume ± button on the remote (or the volume knob), move the arrow cursor down to the line that reads “audio connectors” and press en- ter (or mute on the front panel). Press volume – to move to 1: Digital 2 and press enter (mute) again. Then move the arrow cursor down to the line that defines which connector is being used, and press enter (mute) again. With the cursor changed to an arrow within a diamond ( → ) instead of an ar- row, the volume ± buttons or the knob will allow you to select whatever digital input connector you used in Step 1. When done, press enter (mute) again to save your change.

4PRESS MENU THREE TIMES TO EXIT THE MENU SYSTEM, AND ENJOY

Make sure the volume is on at a low level before you fire up your CD player, press the cd button, and raise the volume to a comfortable level. Ac- cording to the factory defaults (which you can easily change), cd is preset to come on in 2-channel/surround off. You should properly calibrate the system so all speakers are playing at the proper volumes before you listen critically to multichannel audio. Performing this calibration only takes only a few more minutes, but you should read up on it a bit first. You can enjoy the AVP2 in regular stereo until then.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents AVP2 Page Important Safety Instructions Table of Contents Important note About your subwoofer 86-88 Them Maximizing the Value Your PurchaseUnpacking and Placement Serial number Register your purchase Operating Voltage Frequency Word About Installation Quickest Start CD & DVD Quick Start For CD Quick Start For DVD Special Design Features S E R Front PanelTip Surround Mode Display Intensity Delay Mute Center A l o g i n p u t s G i t a l i n p u t s D e o P u t s Rear PanelMale RCA Male XLR Connect to source Video connector Balanced Main Outputs L, C, R Record Outputs Digital Output 15 RS-232 Port IR Input Installation Note Page Remote Control So the menu item may Using The Menu System Page Once in the menu system, the front panel equivalents are Operate Menu Important Note Page Display timeout Display of text Display background color Page Maximum volume Late night SET Configuration Setup MenuDefine source buttons Example setting up a cd transport Renaming source buttons Defining the input type Setting audio delay Choosing a 2-channel mode Page Move to the 1 Item in the MENU, Press the Enter Button Arrow cursor will change to the change-it cursor → Setting & saving input levels Turn the Master Volume Control on the AVP2 Down Set speakers SET Speakers SET Configuration Front L&R 70Hz HPF Center 80Hz HPF Rear L&R 80Hz HPF Special tip Enter the SET Distance Menu Save ALL Your Changes and Return to the SET Speakers Menu Repeat this Process for Each Speaker in Turn Enter the Bass Level Manager Menu and Choose Test Signal on Surround Mode Defaults Defaults Disabled Select the Surround Mode YOU would Like to Modify Page Custom Menu Enter the Setup Menu Select CUSTOM, and then Teach Remote Displays the status screen Select Dolby Pro Logic II Music Trigger settings Enter the Custom Menu Toggle the Menu Item from Remote to Local About… Menu Using the Special Menu Source DVD Using the AVP2 Overload DTS-ES Matrix DTS-ES Discrete Dolby pro logic Stereo surround Mono surround Page Page System Planning Guide Additional notes on speaker placement Your System Settings Page Page Page Page Page Page THX THX Troubleshooting Page Care and Maintenance Canadian Warranty Obtaining Service Specifications 17.26 DimensionsRack Mount Kit Page Madrigal, Inc. All rights reserved

AVP2 specifications

Madrigal Imaging's AVP2 is an advanced multi-channel audio and video processor that has garnered attention for its exceptional performance and innovative features. This state-of-the-art device is designed specifically for high-end home theater systems, providing users with an immersive audio-visual experience.

One of the standout features of the AVP2 is its support for multiple audio formats, including Dolby Atmos and DTS:X. These immersive sound technologies enable users to experience movies and music in three-dimensional audio, allowing them to feel as though they are right in the middle of the action. The AVP2 also supports high-resolution audio formats, making it an ideal choice for audiophiles who demand the best in sound quality.

The AVP2 employs advanced digital signal processing (DSP) technology, which enhances sound clarity and accuracy. With precise calibration and tuning options, users can tailor their audio experience to suit their specific preferences and room acoustics. This DSP technology also enables the AVP2 to deliver superior surround sound, ensuring that every detail of the audio mix is preserved.

For video processing, the AVP2 supports 4K resolution and HDR (High Dynamic Range), allowing users to enjoy stunning picture quality with vibrant colors and enhanced contrast. The processor is equipped with advanced scaling technology that upscales lower-resolution content to near-4K quality, ensuring that all media looks its best.

Connectivity is another key aspect of the AVP2. It features multiple HDMI inputs and outputs, along with various analog and digital audio connections, ensuring compatibility with a wide range of source devices, including Blu-ray players, gaming consoles, and streaming devices. The AVP2 also includes network connectivity options, allowing users to stream content directly from their favorite services.

In addition to its impressive technical specifications, the Madrigal Imaging AVP2 is designed with user-friendliness in mind. Its intuitive interface and remote control provide easy access to all settings and features. Overall, the AVP2 represents a perfect marriage of cutting-edge technology and user-centric design, making it an outstanding choice for anyone looking to elevate their home entertainment setup.
Top Page Image Contents