Madrigal Imaging AVP2 owner manual Balanced Main Outputs L, C, R

Page 26

Installation Note:

26

S-video (Y/C) signals are more susceptible to degradation over long wire runs. The quality of wire used makes a significant difference, but regardless, it is generally inadvisable to run S-video cables more than twenty feet (6 meters). Composite video signals tend to hold up better over longer runs, especially when high quality 75Ω cable such as Madrigal MDC-2 is used.

8BALANCED MAIN OUTPUTS (L, C, R)

The pin assignments of these XLR-type male outputs conform to the inter- national AES standard, and are as follows:

 

Pin 1: Signal ground

1 2

Pin 2: Signal + (non-inverting)

3Pin 3: Signal – (inverting)

Connector ground lug: chassis ground

Refer to your power amplifier’s operating manual to verify that the pin as- signments of its input connectors correspond to the Audio Video Preampli- fier. If not, wire the cable so that the appropriate output pin connects to the equivalent input pin, or reverse the leads of both your speaker cables to “re- verse the reversal” and restore correct polarity.

High quality single-ended outputs are also provided for compatibility with power amplifiers lacking balanced inputs.

Connect the left-front, center and right-front outputs of the Audio Video Preamplifier to the corresponding inputs on your power amplifier(s).

9SINGLE-ENDED MAIN OUTPUTS (ALL CHANNELS)

The first six of these eight RCA connectors provide the main 5.1 channels normally associated with a high quality multichannel system: the left-front, center and right-frontoutputs of the AVP2 are duplicated here in single- ended form (for compatibility with power amplifiers lacking any balanced input capabilities), along with the left-surround, right-surroundand subwoofer channels. Connect these outputs to the corresponding power amplifier channels.

In addition, two “auxiliary” output channels are provided, labelled aux 1 and aux 2. These channels are used for any of several applications such as support for 7.1 channel systems (using either separate side and rear chan- nels Dual Drive™ surrounds), or as additional subwoofer channels. Select the best use for your particular system in the Setup Menu, according to your speaker configuration.

10REMOTE ZONE OUTPUTS

The AVP2 includes a second signal path (beyond the primary one used in the main listening room) that can feed a remote zone, or a record path for making recordings, or both. There is one limitation: the remote and record outputs always contain the same signal.

Page 25 Page 27
Image 26
Page 25 Page 27
Contents AVP2 Page Important Safety Instructions Table of Contents Important note About your subwoofer 86-88 Maximizing the Value Your Purchase ThemUnpacking and Placement Serial number Register your purchase Operating Voltage Frequency Word About Installation Quickest Start CD & DVD Quick Start For CD Quick Start For DVD Special Design Features Front Panel S E RTip Surround Mode Display Intensity Delay Mute Center Rear Panel A l o g i n p u t s G i t a l i n p u t s D e o P u t sMale RCA Male XLR Connect to source Video connector Balanced Main Outputs L, C, R Record Outputs Digital Output 15 RS-232 Port IR Input Installation Note Page Remote Control So the menu item may Using The Menu System Page Once in the menu system, the front panel equivalents are Operate Menu Important Note Page Display timeout Display of text Display background color Page Maximum volume Late night Setup Menu SET ConfigurationDefine source buttons Example setting up a cd transport Renaming source buttons Defining the input type Setting audio delay Choosing a 2-channel mode Page Move to the 1 Item in the MENU, Press the Enter Button Arrow cursor will change to the change-it cursor → Setting & saving input levels Turn the Master Volume Control on the AVP2 Down Set speakers SET Speakers SET Configuration Front L&R 70Hz HPF Center 80Hz HPF Rear L&R 80Hz HPF Special tip Enter the SET Distance Menu Save ALL Your Changes and Return to the SET Speakers Menu Repeat this Process for Each Speaker in Turn Enter the Bass Level Manager Menu and Choose Test Signal on Surround Mode Defaults Defaults Disabled Select the Surround Mode YOU would Like to Modify Page Custom Menu Enter the Setup Menu Select CUSTOM, and then Teach Remote Displays the status screen Select Dolby Pro Logic II Music Trigger settings Enter the Custom Menu Toggle the Menu Item from Remote to Local About… Menu Using the Special Menu Source DVD Using the AVP2 Overload DTS-ES Matrix DTS-ES Discrete Dolby pro logic Stereo surround Mono surround Page Page System Planning Guide Additional notes on speaker placement Your System Settings Page Page Page Page Page Page THX THX Troubleshooting Page Care and Maintenance Canadian Warranty Obtaining Service Specifications Dimensions 17.26Rack Mount Kit Page Madrigal, Inc. All rights reserved

AVP2 specifications

Madrigal Imaging's AVP2 is an advanced multi-channel audio and video processor that has garnered attention for its exceptional performance and innovative features. This state-of-the-art device is designed specifically for high-end home theater systems, providing users with an immersive audio-visual experience.

One of the standout features of the AVP2 is its support for multiple audio formats, including Dolby Atmos and DTS:X. These immersive sound technologies enable users to experience movies and music in three-dimensional audio, allowing them to feel as though they are right in the middle of the action. The AVP2 also supports high-resolution audio formats, making it an ideal choice for audiophiles who demand the best in sound quality.

The AVP2 employs advanced digital signal processing (DSP) technology, which enhances sound clarity and accuracy. With precise calibration and tuning options, users can tailor their audio experience to suit their specific preferences and room acoustics. This DSP technology also enables the AVP2 to deliver superior surround sound, ensuring that every detail of the audio mix is preserved.

For video processing, the AVP2 supports 4K resolution and HDR (High Dynamic Range), allowing users to enjoy stunning picture quality with vibrant colors and enhanced contrast. The processor is equipped with advanced scaling technology that upscales lower-resolution content to near-4K quality, ensuring that all media looks its best.

Connectivity is another key aspect of the AVP2. It features multiple HDMI inputs and outputs, along with various analog and digital audio connections, ensuring compatibility with a wide range of source devices, including Blu-ray players, gaming consoles, and streaming devices. The AVP2 also includes network connectivity options, allowing users to stream content directly from their favorite services.

In addition to its impressive technical specifications, the Madrigal Imaging AVP2 is designed with user-friendliness in mind. Its intuitive interface and remote control provide easy access to all settings and features. Overall, the AVP2 represents a perfect marriage of cutting-edge technology and user-centric design, making it an outstanding choice for anyone looking to elevate their home entertainment setup.
Top Page Image Contents