JVC GRDVL140 26 EN, Programme AE With Special Effects, To Deactivate Night-Scope

Page 26

Set the Power Switch to “ ” while pressing down the Lock Button located on the switch.

26 EN

NOTES:

●During Night-Scope, the following functions or settings cannot be activated and its indicator blinks or goes out:

•Some modes of “Programme AE With Special Effects” ( pg. 26, 27), “Picture Wipe/Dissolve” ( pg. 28, 29).

•“GAIN UP” in the CAMERA Menu ( pg. 35).

•“DIS” in the MANUAL Menu ( pg. 35).

●During Night-Scope, it may be difficult to bring the camcorder into focus. To prevent this, use of a tripod is recommended.

MENU/BRIGHT Wheel

Lock Button

Power Switch

NIGHT-SCOPE Button

P.AE Button

Display

SHUT TER1/120

SPORTS

SNOW

SPOT L I GHT

TW I L I GHT

SEP I A

MONOTONE

CLASS I C F I LM

STROBE

SLOW 4X

SLOW 1 0X

FOR RECORDING (cont.)

Night-Scope

Makes dark subjects or areas even brighter than they would be under good natural lighting. Although the recorded image is not grainy, it may look as if it is strobing due to the slow shutter speed.

1

2 Press NIGHT-SCOPEso that the Night-Scope indicator “ ”appears.

•The shutter speed is automatically adjusted to provide up to 30 times sensitivity.

•“A” appears beside “ ” while the shutter speed is being automatically adjusted.

To Deactivate Night-Scope . . .

.... press NIGHT-SCOPEagain so that the Night-Scope

indicator disappears.

Programme AE With Special Effects

1 Set the Power Switch to “ ” while pressing down the Lock Button located on the switch.

2 Press the MENU/BRIGHT wheel in. The Menu Screen appears.

3 Rotate the MENU/BRIGHT wheel to select “ PROGRAM AE”, then press it.

4 Rotate the MENU/BRIGHT wheel to select the desired mode ( pg. 27), then press it. Selection is complete. Press the MENU/BRIGHT wheel in again. The Menu Screen closes.

5 Press P.AE so that the selected effect indicator appears.

To Deactivate The Selected Mode . . .

.... press P.AE again so that the effect indicator disappears.

NOTES:

●Programme AE with special effects can be changed during recording or during Record-Standby.

●Some modes of Programme AE special effects cannot be used during Night-Scope.

IMPORTANT:

Some modes of Programme AE with special effects

cannot be used with certain Fade/Wipe Effects

( pg. 28, 29). If an unusable mode is selected, its indicator blinks or goes out.

Image 26

Contents GR-DVL140 AC Adapter until It is recommended that youUnit, first firmly Some DO’S and DON’TS on the Safe USE of Equipment Before recording an important scene Make sure you only use cassettes with the Mini DV markBN-V408U Power Cord Cable AdapterLens Cap Core Filter xHow To Attach The Core Filter Release the stoppers on both ends of the Core FilterContents Getting StartedTo Detach The Battery Pack PowerCharging the Battery Pack Slide BAT. Release and pull out the battery packPerform of Charging the Battery Pack pg Using the Battery PackUsing AC Power Approximate recording time10 EN Grip AdjustmentViewfinder Adjustment Shoulder Strap Attachment Tripod MountingDate/Time Settings 12 ENCamcorder needs to be powered up to load or eject a cassette Loading/Unloading a Cassette14 EN Recording Mode SettingSet the tape recording mode depending on your preference Basic Recording & Playback Basic Recording PlaybackBasic Recording 16 ENBasic Recording Journalistic Shooting Operation ModePower Switch Position Manual SELF-RECORDINGZoom Slide the Power Zoom Lever towards T18 EN Zoom OutProper recording When a blank portion is recorded on a tapeTime Code 20 EN Load a tape pg Set the Power Switch toTo Control The Speaker Volume BasicPress Blank Search To cancel Blank Search midwayBlank Search Connections If your TV/VCR has a 21-pin connector22 EN CamcorderIf using a VCR . . . go to step If not . . . go to step EN23Advanced Features 24 ENFor Recording Feature Auto FocusFeature Manual Focus To obtain correct focusNight-Scope To Deactivate The Selected Mode26 EN Programme AE With Special EffectsSlow Slow Shutter Gives recorded scenes a strobe effectYour recording looks like a series of consecutive snapshots FADE/WIPE Selection 28 ENFade/Wipe Effects Picture Wipe or Dissolve SelectionFader And Wipe Menu Menu EffectSnapshot Snapshot Mode Selection30 EN Snapshot RecordingEN31 Iris Lock 32 ENExposure Control To Return To Automatic White Balance White Balance AdjustmentManual White Balance Operation To Change The Tint For RecordingSee pg EN Using Menus for Detailed AdjustmentIf you have selected WIPE/FADER Program AE or W. Balance System or DisplayMenu Screen Explanations Screen ratio becomes Factory setting isNormal screen ratio VerticallyAutomatic demonstration will not take place Does not reset all settings to the factory-presetResets all settings to the factory-preset Appearing on the connected TV screenYour preference pg Mode SP or LP depending onPower Switch is set to pg SYSTEM, which appears whenPlayback Sound DisplayDubbing To a VCR 40 ENDubbing EN41 EN Using the Optional Remote Control Unit Installing The BatteryEN43 Functions ButtonsPress Play 4 to find the scene of interest Feature Playback Zoom44 EN To press VCR CTL for this one SET REMOTE/VCR CodeVCR Recording deck You are now ready to try Random Assemble EditingVCR other than above JVC VCR equipped with a remote pause connectorMake Connections Cancelled and editing will not take place Select ScenesAutomatic Editing to VCR Diagnosing VCR/CAMCORDER Timing Adjustment of VCR/CAMCORDER TimingFor More Accurate Editing To hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen pgAudio Dubbing Using PC connection cable Using DV cableConnection To a Video Unit Equipped With a DV Connector 52 ENReferences Time required to calculate and display the remaining tape When you use the LCD monitor outdoors in direct sunlight,Cassette holder cannot be opened unless a power supply is Corrective Action TroubleshootingClean the lens and check Replace with new cassetteTroubleshooting 56 ENEN57 58 EN EN59 60 EN 5 6 @ # $Audio/Video Output Connector pg , 40 Dioptre Adjustment Control pg Battery Release SwitchFast-Forward Button pg Backlight Button @ Power Switch Power Lamp pg62 EN LCD Monitor/Viewfinder Indications During RecordingBright Displays the brightness of the LCD Displays the sound modeLCD Monitor/Viewfinder Indications During Playback Switch is set to or pg Displays the battery remaining powerAppears when no tape is loaded pg Cleaning cassette pgTurn off the camcorder User MaintenanceAfter Use Cleaning The Camcorder Press Push Here to close the cassette holder66 EN About moisture condensation Do not leave the unitTo protect the unit, do not Serious malfunctioning68 EN TermsEN69 Time Code pg , 37, 3870 EN AC 110 V to 240 V`, 50 Hz/60 Hz Power requirementApprox g not including Power Cord DC 11GR-DVL140