JVC GR-AXM405 No power is supplied, Recording does not start, Animation or Time-Lapse is not

Page 50

50EN

TROUBLESHOOTING

If, after following the steps in the chart below, the problem still exists, please consult your JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.) and clock battery; and then re-connect it and proceed as usual from the beginning.

SYMPTOM

 

POSSIBLE CAUSE(S)

POWER

 

 

No power is supplied.

 

● The battery pack has not been attached correctly

 

 

(☞ pg. 4).

 

 

● The battery pack is not charged (☞ pg. 4).

 

 

● The power supply has not been correctly connected

 

 

(☞ pg. 5).

 

 

 

The power suddenly goes off and

 

● The battery pack has completely discharged.

does not come back on by itself.

 

● Remove the cassette and disconnect the power source, then

 

 

after a few minutes, try turning the power back on. If it still

 

 

does not come on, consult your nearest JVC dealer.

 

 

 

RECORDING

 

 

Recording cannot be performed.

 

● Make sure the Erase Protection tab is in the position that

 

 

allows recording. If not, slide the tab. Some cassettes have

 

 

removable tabs. If the tab has been removed, cover the

 

 

hole with adhesive tape.

 

 

 

Recording does not start.

 

● The camcorder Power Switch has not been set to

 

 

“CAMERA” (“AUTO” or “PRO.”) (☞ pg. 12).

 

 

 

Animation or Time-Lapse is not

 

● Before recording in the Animation mode at the very

available.

 

beginning of a tape, set the camcorder to the Recording

 

 

mode for about 5 seconds, so that the tape runs smoothly.

 

 

Using the Fade-in function at this point is a good way to

 

 

begin an animated program (☞ pg. 35, 43).

 

 

 

PLAYBACK

 

 

The tape is running, but there is no

 

● The TV has not been set to its VIDEO mode or channel.

playback picture.

 

● If A/V connection is used, the TV’s VIDEO/TV Switch has

 

 

not been set to VIDEO.

 

 

 

Playback picture is blurred or

 

● The video heads are dirty or worn out. Consult your nearest

interrupted.

 

JVC dealer for head cleaning or replacement.

 

 

 

The counter indication is blurred

 

● This is normal.

during Still playback.

 

 

 

 

 

TAPE TRANSPORT

 

 

The tape stops during fast-forward or

 

● The Counter Memory Function has been activated

rewind.

 

(☞ pg. 38).

Rewinding or fast-forwarding cannot

● The tape is already fully wound on one reel or the other.

be performed.

 

Page 49 Page 51
Image 50
Page 49 Page 51
Contents GR-AXM405 GR-AXM205 Dear Customer It is recommended that youContents Using the Battery Pack PowerCharging the Battery Pack Discharged Using AC PowerUsing a CAR Battery Clock Lithium Battery Insertion/Removal Getting StartedDate/Time Settings EN Getting Started Recording Mode SettingTape Length Setting ContLoading/Unloading a Cassette Grip Adjustment Viewfinder AdjustmentTripod Mounting Adjust LengthShoulder Strap Attachment Attach StrapLoad a Cassette Power Switch PositionBasic Recording Start ShootingRecording Stop RecordingPress Display Button Before the following steps, perform pg Recording Basic RecordingShooting While Watching The LCD Monitor Brightness Control Journalistic ShootingInterface Shooting Zoom EN Recording Basic FeaturesPush the Power Zoom Lever towards T Zoom OutFeature Quick Review To check the end of the last recordingFeature 5Sec. Rec 5-sec. Recording GR-AXM205 only Basic FeaturesFeature Picture Stabilizer Press P. STABILIZER. appearsBattery power Feature Video Light GR-AXM405 onlyTo brighten the scene when natural lighting is too dim Take Snapshot Recording Advanced FeaturesSnapshot GR-AXM405 only If you press during Record-StandbyStart or END Recording Fade/WipeEngagemode FADE- or WIPE-STANDBY Programme AE With Special Effects Advanced FeaturesSelect Mode Press P.AE to cycle through the modes as shown on the leftHigh shutter speed clearly captures fast-moving action Display ModeNega Posi mode Colours of a picture are reversedDate/Time Insert Press the Select Dial to display the Menu ScreenInstant Titles Access Title MenuSelect the Desired Mode END Setting Using Menu For Detailed AdjustmentMake Setting Menu Screen Explanations Menu Screen Available Using The Select DialMenu Screen Available Using The Menu Button Allows you to set the current date and time pg Tally lamp comes on to signal the start of recordingDemo Mode is set to on and the Menu Screen is closed Recording pgAdjust Exposure Access Exposure MenuAccess Manual Exposure END Adjustment of ExposureAuto Focus FocusingRecording Patterns that are regularly repeatedAdjust Focus Access Focus MenuAccess Manual Focus END Adjustment of FocusSET Function Parameters White Balance AdjustmentAccess White Balance Adjustment To Return To Automatic White BalanceSET Manual White Balance Enter SettingManual White Balance Operation To Change The Tint For RecordingStart Delayed Recording Self-TimerAccess INT. Time Menu SET Interval TimeAnimation Time-LapsePlay Back Playback Basic PlaybackRewind or Fast-Forward the tape Stop PlaybackAdjust Volume Playback FeaturesSpeaker Volume Control TrackingFeature Shuttle Search Playback FeaturesFeature Still Playback Feature Counter Memory FunctionCassette Adapter Using The Cassette Adapter EN39Insert Battery Basic Connections When connecting the cables, open this coverBasic Connections And Tape Dubbing Connection For Tape DubbingTape Dubbing Functions Installing The BatteryPull OUT Battery Holder ButtonsAnimation Feature Self-Timer, Animation and Time-LapseSelf-Timer Time-LapseSET REMOTE/VCR Code Using the Remote Control UnitCreate edited videos easily using your camcorder as Operate VCRVCR Other than Type or Make ConnectionsJVC VCR Equipped with Remote Pause Terminal Prepare CamcorderRegister END of Scene Select ScenesStart Source Playback At the bottom of the screenAutomatic Editing to VCR Supplemental Information on the Remote ControlHow to use EN Using the Remote Control Unit Insert EditingEND Audio Dubbing Audio DubbingBegin Audio Dubbing Animation or Time-Lapse is not No power is suppliedRecording does not start AvailableDuring recording, the indications do not appear An error number i.e. E03 appearsReview or Retake mode Tape will not eject52EN Power Switch Battery Release Switch Dioptre Adjustment Control Lens Cover Open/Close RingVideo Light Switch Light OFF/AUTO/ON DC in Jack Connectors w to r are located beneath the coverIndex Indications During use For safety, do notTo avoid hazard Store cassettesCleaning The Camcorder Avoid using the unitTo prolong service life Do not leave the unitGeneral ConnectorsProvided Accessories Optional Accessories Memo Memo GR-AXM205
Top Page Image Contents