JVC GR-SXM201AS, GR-SXM301AS, GR-SXM265AS, LYT1367-001A manual Unit, Using the Remote Control

USING THE REMOTE CONTROL UNIT (GR-SXM301/265AS only)

UNIT

The Remote Control Unit can operate this camcorder from a distance as well as the basic operations (Playback, Stop, Pause, Fast-Forward and Rewind) of your VCR. Make sure the remote control is pointed at the remote sensor.

ZOOM (T/W)				START/STOP
PLAY	T	W
			START/
			STOP
REW	REW	PLAY	FF	PAUSE
		STOP	PAUSE
				FF
INSERT	REC TIME		INT. TIME	A.DUB
STOP	INSERT		A.DUB
REC TIME/	TIME LAPSE			INT. TIME
	ANIM.	SELF TIMER

ANIM.

Playback Zoom (GR-SXM301AS only)

To magnify the recorded image up to 10X at any time during playback. Make sure that the TBC mode is activated.

1)Press PLAY to find the scene of interest.

2)Press ZOOM (T/W). Pressing T zooms in. To end zoom press and hold W until magnification returns to normal. Or, press STOP and then

press PLAY.

•Due to digital image processing, the quality of the image may suffer.

Animation And Time-Lapse

The remote control lets you set/release interval time and recording time without setting REC TIME/INT. TIME ( pg. 15) in SYSTEM MENU.

Animation

Each time ANIM. is pressed, the recording time changes in the following order: 1/4S, 1/2S, 1S, 5S and no indication (off).

Time-Lapse

Each time REC TIME is pressed, the recording time changes in the following order: 1/4S, 1/2S, 1S, 5S and no indication (off). Each time INT. TIME is pressed, the interval time changes in the following order: 15S, 30S, 1MIN, 5MIN and no indication (off).

Insert Editing

You can record a new scene onto a previously recorded tape. Only the video signal is recorded in this mode.

1)Set the Power Switch $ to “PLAY” while pressing down the Lock Button # located on the switch.

2)Play back the tape, locate the edit-out point and press PAUSE . Perform steps 2) through 5) of “COUNTER MEMORY” (pg. 16)

3)Press REW to go a little beyond the beginning of the scene you want to replace, press PLAY to view the recorded tape, and press PAUSE

exactly at the edit-in point where the new scene should start.

4)While holding down INSERT, press and release PAUSE. 4 appears.

5)To begin Insert Editing, press START/STOP. When the counter reaches “0:00:00”, editing stops automatically and the camcorder enters the Insert-Pause mode. To end Insert Editing, press STOP.

•During Insert Editing, the original audio will be heard from the speaker.

•After step 4), “Retake” ( pg. 10) can be performed.

•The tape may stop slightly before or after the designated end point, and noise bars may appear. Neither indicates a defect in the unit.

Audio Dubbing

You can record a new soundtrack on a prerecorded tape (normal audio only). The sound is recorded from the built-in microphone.

Perform steps 1) and 2) of the Insert Editing procedure.

1)Press REW to go a little beyond the beginning of the scene onto which you want to dub the new audio, press PLAY to view the recorded tape, then press PAUSE at exactly the point where dubbing should start.

2)While holding down A. DUB, press and release

PAUSE.

3)To begin Audio Dubbing, press PLAY. When the counter reaches “0:00:00”, Audio Dubbing stops automatically and the camcorder enters the Audio Dub-Standby mode. To end Audio Dubbing, press STOP.

•Do not press REW or FF during Audio Dub- Standby, or the edit points will not be accurate.

•If the microphone is too close to the TV, or if the TV’s volume is too high, whistling or howling may occur.

For Insert Editing/Audio Dubbing

•Insert Editing and Audio Dubbing may not work correctly if the tape contains blank segments, or if the recording speed was changed during the original recording.

•To edit/dub onto a tape, make sure the erase protection tab is in the position that allows recording.

•Do not press STOP during Insert Editing or Audio Dubbing, or the edit points will not be accurate.

USING THE REMOTE CONTROL

17