JVC GR-SXM245 manual For Your Maintenance, To prevent damage to the LCD monitor, do not

Page 27

LCD Monitor

1.To prevent damage to the LCD monitor, DO NOT . . .

.... push it strongly or apply any shocks.

.... place the camcorder with the LCD monitor on the bottom.

2. To prolong service life . . .

.... avoid rubbing it with coarse cloth.

3.Be aware of the following phenomena for LCD monitor use. These are not malfunctions:

While using the camcorder, the surface around the LCD monitor and/or the back of the LCD monitor may heat up.

If you leave power on for a long time, the surface around the LCD monitor becomes hot.

About moisture condensation . . .

You may have observed that pouring a cold liquid into a glass will cause drops of water to form on the glass’ outer surface. This same phenomenon occurs on the head drum of a camcorder when it is moved from a cool place to a warm place, after heating a cold room, under extremely humid conditions or in a place directly subjected to the cool air from an air conditioner.

Moisture on the head drum can cause severe damage to the video tape, and can lead to internal damage to the camcorder itself.

Serious malfunctioning

If malfunctioning occurs, stop using the unit immediately and consult your local JVC dealer.

For Your Maintenance

1.After Use

1 Set the Power Switch to “OFF” to turn off the camcorder.

2 Open the LCD monitor to an angle of over 60 degrees. Slide EJECT to open the cassette holder, then remove the cassette.

3 Close and lock the cassette holder by pressing the Close button.

4 Close and lock the LCD monitor.

5 Slide BATTERY RELEASE to remove the battery pack.

6 Attach the provided lens cap to the camcorder’s lens.

2.Cleaning The Camcorder

1Wipe gently the exterior with a soft cloth. Put cloth in diluted mild soap and wring it well to wipe off heavy dirt, then wipe again with a dry cloth.

2Open the LCD monitor and wipe it gently with a soft cloth. Be careful not to damage the monitor. Close the LCD monitor.

3Blow the lens with a blower brush, then wipe it gently with lens cleaning paper.

4Turn the eyepiece counterclockwise and pull it out.

5Remove dust from the viewfinder using a blower brush.

6Re-attach the eyepiece and turn it clockwise.

Avoid using strong cleaning agents such as benzine or alcohol.

Cleaning should be done only after the battery pack has been removed or other power units have been disconnected.

Mold may form if the lens is left dirty.

When using a cleaner or chemically treated cloth, refer to the cautions that came with it.

When removing the eyepiece, be sure to hold the viewfinder securely.

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Change or modifications not approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

27

Image 27
Contents Automatic Demonstration Dear CustomerFor Customer Use AP-V12U, AP-V11U or AP-V10U Provided AccessoriesP7U BN-V11U Shoulder Strap Lens Cap AA R6 Battery AC Adapter Cassette AdapterSafety Precautions PrecautionsImportant Safety Instructions LCD Monitor/Viewfinder, Indications Pg , 10 IndexGetting Started Charging the Battery PackUsing the Battery Pack Using AC PowerWith AM or PM Date/Time SettingsShoulder Strap Attachment Grip AdjustmentViewfinder Adjustment 180CONTROLS, Connectors and Indicators Volume - - -6- - - +LCD Monitor/Viewfinder Indications Stabilizer Recording Playback Shooting while using the viewfinder Make sureShooting while using the LCD monitor Make To Adjust The Brightness Of The LCD MonitorBasic Features Picture Stabilizer5Sec. Rec 5-sec. Recording Retake ZoomingVideo Light Quick ReviewTracking TBC Time Base CorrectorCounter Memory Audio Input Connections To a TV/VCRTape Dubbing To TV or VCRVHS VCR Using The Cassette AdapterInstructions Exposure Menu SettingsCamera Menu FocusDATE/TIME Disp TitleWide REC ModeSystem Menu ZoomREC Time Tape LengthDisplay OSD OutputDATE/TIME Demo ModeTele Macro Title LangFade/Wipe Effects Advanced FeaturesDigital Effects Program AE With Special EffectsAnimation or Time-Lapse is not available TroubleshootingMain Unit General Battery PrecautionsBattery Packs CassettesTo prevent damage to the LCD monitor, do not For Your MaintenanceOptional Accessories SpecificationsUSO DE LA Alimentación DE CA Español AlimentaciónCarga DE LA Bateria USO DE LA BateriaPage Compartimiento de cassette Español Guia Para Operacion RapidaColocación/Extracción de un cassette GrabaciónReproducción Cargue una cintaPara Grabació N DE VÍDEO/REPRODUCCION DE Vídeo