JVC GY-DV550 Using AN ANTON-BAUER Battery Pack, Precautions for the Battery Pack

Page 21

4. POWER SUPPLY

4-2 Battery Pack Operation (Cont'd)

USING AN ANTON-BAUER BATTERY PACK

4. POWER SUPPLY 4-2 Battery Pack Operation (Cont'd) REMAINING BATTERY POWER DISPLAY

To use an Anton-Bauer battery pack (Propack 13/14, Trimpack 13/14, Magnum 13/14, Compack 13/14 Series), it is necessary to detach the battery case from the GY-DV550 and replace it with the Anton-Bauer battery holder. Use the following battery holder.

Battery holder: Anton-Bauer QRQ27

Detaching the Battery Case From the GY-DV550 and Attaching The Anton-Bauer Battery

WARNING indicator

 

Remaining battery

 

power indication

TALLY

E

BATT

F

 

 

 

lamp

 

 

 

 

E

BATT

 

To display the remaining battery power accurately, set the VCR Setup Menu item No. 396 BATTERY TYPE according to the type of the battery pack in use.

See page 75.

The status of the remaining battery power can be checked by the remaining battery power indication.

See page 24.

 When the remaining battery power is nearly exhausted, the

following warning messages will appear. In this case, replace

 

2.

 

1. Black screw A

1. Remove the two black screws A on the battery case.

2.

Remove the lower half of the battery case cover in the

 

downward direction.

Connector

Compartment

5.

 

Viewfinder

 

LOW BATTERY

BATT lamp

REC

BATT ALARM

with a fully charged battery as soon as possible.

Remaining battery power indication:

Segment bar and "BATT" indicator start to blink

WARNING indicator and TALLY lamp blink

Viewfinder:

BATT lamp lights.

TALL lamp blinks.

During status 1 mode, the voltage display flashes.

Alarm sound beeps

3.

Mount screw B

 

3. Connector

5.

4.

 

Anton-Bauer

 

Battery holder

4. Connect the connectors protruding from the GY-DV550 with

After the remaining battery power warnings appear, the GY-DV550 automatically stops operation if the battery power operation is continued.

3.

Mount screw

 

B

the connectors on the battery holder.

*Following connection of the connectors, insert them into the connector compartment.

5.

Secure the battery holder to the GY-DV550 with the four

 

mount screws provided with the battery holder.

Operating Time with Battery Pack

When the VF-P115B is used as the viewfinder and a fully

charged battery pack is attached, the approximate continuous

operating time is as follows:

Battery Pack

Continuous Operating Time (at 25 ˚C)

Battery operating time may differ depending on the number

of times the battery has been charged, charging conditions

and the operating environment, etc. Use the values in the

table on the left for approximate reference times.

Operating time is reduced in areas with a cold environment.

3. To remove the battery case, remove the four screws B fixing

* Take

care

not

to pinch the wires. This could result in

the battery case and the connector connecting the battery

damage.

 

 

case to this unit.

 

 

 

 

 

 

Attaching and Detaching an Anton-Bauer Battery Pack

NP-1B

60 minutes

Magnum 14

130 minutes

NP-L40

80 minutes

Operating time is reduced when the power zoom lens is used

frequently.

Guide pins

PRECAUTIONS FOR THE BATTERY PACK

Release lever

Cassette cover

 

side panel

Battery

Guide holes

pack

(x3)

(Trimpack)

 

Release lever

Attaching the Battery Pack

1. Align the 3 guide pins of the battery pack with

 

the guide holes on the battery holder, and push

 

straight to insert the battery pack.

 

The battery cannot be attached properly if the

 

guide pins are not inserted straight.

2.

Slide the battery pack toward the side panel

 

where the cassette cover is located until it clicks.

 

Now the battery pack has been attached.

Detaching the Battery Pack

When the battery pack is not in use, it must be stored in a cool, dry place.

Do not leave the battery pack in a place where it might be subject to a high temperature (under direct sunlight in a car, etc.), this could cause leakage of the fluid or shorten service life.

When the terminal section of the battery pack gets dirty, the operating time will be shortened.

If the operating time becomes greatly reduced even immediately after recharging, the service life of the battery pack is nearly finished. Purchase a new battery pack.

Recharging

Recharge the battery pack after completely discharging it. Repeated recharging with residual charge remaining could result in reduced battery capacity.

If the battery capacity is reduced by repeating incomplete recharging, or recharging without discharging, once discharge the battery pack completely, then recharge it to restore the battery capacity.

If the battery pack is recharged with its internal temperature raised immediately after use, recharging may not be performed completely.

Side panel with display

Battery

While pushing and holding the release lever, slide the battery pack toward the side panel where the LCD display is located, then pull the battery pack outward to remove.

39

40

Image 21
Contents For Customer Use SC96999 U ModelSC961000 E Model Port Cable Length PortCable Length Information Literature accompanying the applianceInterference by one or more of the following measures Main Features Main Unit ConfigurationIntroduction Time Code OperationPrecautions for Proper Use Routine and Periodical MaintenanceHead Cleaning Periodical MaintenanceCharacteristic CCD Phenomena Battery Pack to be UsedVideocassette to be Used Front SectionCamera Setting Section Front Section Cont’dRight Side Section VCR Setting Section Right Side Section Cont’dRight Side Section Contd Time Code Generator setting switches Right Side Section ContdVCR Display Section Left Side Section Adapter Section Top SectionRear Section Rear Section Contd Counter Display ContentsLens optional 1.5-Inch Viewfinder optionalS14 x 7.3B12 VF-P115BViewfinder Screen Display Indications in Viewfinder ContdStatus  Status ScreensIndication Contents  Alarm Message DisplayIndication Indication Contents  Time/Date DisplayBasic System Indication in Viewfinder ContdAttaching the Viewfinder optional Attaching the Microphone optionalAttaching the Zoom Lens optional Provided Microphone How to Install the Lithium Battery Lithium battery CR2032 How to Remove Lithium Batteries Attaching the 4-inch Viewfinder OptionalBattery Pack Operation Contd Power SupplyBattery Pack Operation Attaching a Flat Shape Type Battery PackPrecautions for the Battery Pack Using AN ANTON-BAUER Battery PackPreparations Turning the Power onCassette Loading and Unloading Loading the CassetteCamera Settings Setting the Date and TimeScreen Size 43/169 aspect ratio Mode Selection FilterExternal Monitor Adjustment Viewfinder AdjustmentBrightness and contrast adjustment White Balance Adjustment White Balance AdjustmentLine Switch Settings of the VCR Section How to use the audio input level control Manual Adjustment of Audio Input LevelAlarm Monitor Monitor Select On the front sectionShooting Operation About the Quick REC Start ModeBasic Recording Operation Basic Recording Operation ContdIf Unit is Left in Record-Pause Standby Mode VCR Save ModeRecording from the Save mode VTR switch settingSettings Recording External Video SignalsGENLOCK/AUX ModelPlayback Mode Playback ProcedureRecording with an External VCR Contd Time Code Operation Presetting and Recording of Time CodeFast-Forward, Rewind Displaying Time Code Set the related VCR Setup Menus Presetting Users BIT DataAdvance Preset TC OUT Genlock AUX Monitor OUT Mark Mode SettingExplanation of the S.S.F. Function Reproducing Time Codes10-4 Resetting S.S.F. Data 10-2 How to Use the S.S.F. FunctionCUE Mode Mark ModeWriting S.S.F. Data to Tape Connecting a Video Component with DV ConnectorOutputting S.S.F. Data 10-5Connecting a PC Setup MenuVCR Setup Menu VCR Setup Menu ConfigurationVCR Setup Menu Contents VCR Setup Menu ContdCamera Menu Screen Flow 12-1 VCR Setup Menu ContdTime Code On ScreenVF Display Screen 12-3 How to Select from the Camera MenuOperation Screen 12-6 Process Screen12-5 12-7 Advanced Process Screen Skin Color Adjust ScreenFile Manage Screen Storage OperationTime Date screen Setup ScreenSetting procedure Reset OperationWHT.BAL selector switch ER dialAdjustment of Lens Iris Iris Brightness AdjustmentZebra Pattern Display During Manual Adjustment 13-2Gain Switching 13-4 Gain Sensitivity AdjustmentSwitch Functions  Automatic Setting Contents13-6 How to Use Skin Tone Detail Cont’d 13-6 How to Use Skin Tone Detail Using the Skin Tone Detail Function Skin Tone Detail functionSC Coarse SC Fine Phase Zoom Focus SC Coarse SC Fine Phase Gamma Title Title SETConnection Unavailable functionsTroubleshooting Connecting the camera remote control unit Cont’dAlarm Indications Function of Internal SwitchesAlarm Indications Contd Troubleshooting ContdTroubles with Error Code Outputs 14-1 Troubleshooting ContdError Code Error Details GY-DV550 Operation RemedySymptoms Power cannot be switched on Troubles Without Error Code OutputsHour Meter Display For servicing Hour MeterSpecifications 14-3103U External Dimensions unit mm Specifications