Bogen UDMS800BP, UDMS800HH instruction manual Receiver ASCTM/IR Sync Manual Programming

Page 13

SELECTING THE GROUP/CHANNEL, IR PROGRAMMING,

AND SIMULTANEOUS MULTICHANNEL OPERATION

ing the UP BUTTON (13) or by pressing the MENU BUTTON (14) twice to IR MENU (IR icon will light up for IR function), then press the UP BUTTON (13) to start IR programming.

•To manually select Group/Channel, press the MENU BUTTON (14) once for GROUP (21) selection for Factory PRESET Group 11 to 1A mode or User SELECTABLE Group 1B to 1F mode. Use the UP/DOWN buttons to change the group. After selecting a group, press the MENU BUTTON (14) twice for channel selection menu. Use the UP/DOWN buttons to change the channels (frequencies) that are available in each group.

(Note: for Group11 to 1A, the CH (23) display will indicate the channel number chosen, and for Group 1B to 1F only the letter “U” and the frequency chosen will be displayed. See Frequency Listings section for available channels in each group.)

After finishing channel selection, press the MENU BUTTON (14) once or wait a few seconds for IR MENU, and then press the UP BUTTON (13) to start IR programming.

This completes the GP/CH (frequency) programming. The next section outlines the procedure for sync’ing the receiver’s programmed channel to the transmitter.

Receiver ASCTM/IR Sync Manual Programming

To manually program the pre-selected Group/Channel (frequency) from the receiver to the transmitter, place the transmitter’s IR RECEPTOR SENSOR WINDOW (37) 6-12” away from the receiver’s IR WINDOW (12). Press the MENU BUTTON (14) four times to the IR Screen Display and then press the UP BUTTON (13) to start IR programming. The flashing IR INDICATOR (22) icon indicates IR transmission is in progress. When the synchronization is completed success- fully (usually in less than 2 seconds), the RF INDICATOR (19) and the diversity A or B INDICA- TOR (20) on the receiver will display, indicating that the IR linking is completed. The LCD DISPLAY SCREEN (16) will show the selected channel. If the UP Button is not pressed during the two seconds of active data transfer, the IR INDICATOR (22) will not flash, the LCD Display will revert to the main menu, the receiver will not link to the transmitter, and the transmitter’s previously programmed channel remains unchanged.

Instructions for the Setup of Simultaneous Multichannel Operation

This UDR800 receiver is capable of finding an open channel with its autoscan capability. This built-in feature is a quick, convenient way to set up many wireless systems at the same location for simultaneous multichannel operation.

If you are using multiple transmitters at the same location, set up the first transmitter and leave it ON and keep it 10 feet away from the receivers and 1 foot or more between transmitters. This avoids possible duplicate selection of the same channel as already selected for the first receiver. Then start the autoscan function on the second receiver. Repeat this procedure for all receiver/transmitters to be used in your system. Finally with all the transmitters ON, perform a range walk test in the location these systems will be used in to check for potential crosstalk interference in this application.

If you are not satisfied with any of the channels scanned, repeat the autoscan procedure for that receiver again anytime for finding another free channel. This process can be simplified if you select channels within Factory SELECTED Groups 11 to1A, as the channels within those groups are mutually compatible (unless there is outside interference on any of the selected fre-

11

Page 12 Page 14
Image 13
Page 12 Page 14
Contents UDMS800HH UDMS800BP This Page Intentionally Left Blank Using this Manual ContentsIntroduction UDR800 Receiver System FeaturesAdjusting the Mute Level/RF Squelch Powering the ReceiverUDR800 Receiver Rack Mounting the ReceiverConnecting the Audio Output Audio Level and Peak LED IndicatorDouble Mounting Requires RPK90 UDR800 Rear View UHT800 Handheld MIC Transmitter Microphone Battery InstallationProgramming UHT800 to Selected Group/Channel Frequency Operating the UHT800 Handheld MIC TransmitterUHT800 UBP800 BODY-PACK MIC Transmitter UBP800 Receiver ASCTM/IR Sync GR/CH Frequency Choosing Group/Channel for the SystemReceiver ASCTM/IR Sync Manual Programming Locking Front Panel Controls Front Panel LOCK-OUTFrequency Listings Frequency PlanOverall System Performance SpecificationsLimited Warranty Exclusion of Certain Damages Page Page Spring Street, Ramsey, NJ 07446, U.S.A Tel -934-8500 Fax

UDMS800BP, UDMS800HH specifications

The Bogen UDMS800HH and UDMS800BP are advanced public address systems designed to deliver high-quality sound and reliable performance in various settings. These models are particularly favored in educational institutions, corporate environments, and large venues where effective communication is crucial.

The UDMS800HH features a handheld microphone that allows for mobility and flexibility during presentations or speeches. It utilizes UHF (Ultra High Frequency) technology, ensuring clear audio transmission over long distances with minimal interference. The handheld microphone is lightweight and ergonomically designed for comfortable use during extended periods. The microphone also incorporates a built-in rechargeable battery, providing convenience and reducing the need for constant battery replacements.

On the other hand, the UDMS800BP boasts a belt-pack transmitter, which is ideal for hands-free applications. This model is often paired with lavalier or headset microphones, making it perfect for teachers or presenters who need to move around while engaging their audience. The belt-pack design allows users to clip it onto their waist or belt, providing a wireless experience without the hassle of cords.

Both models are equipped with easy-to-use controls for volume adjustment, channel selection, and power on/off, making it user-friendly for novice and experienced operators alike. The systems feature a robust construction resistant to wear and tear, ensuring durability even in demanding environments.

Another significant characteristic is the wide frequency response and low distortion, which guarantee natural sound reproduction. Bogen's proprietary technologies enhance audio clarity, making them suitable for spoken word applications and musical performances alike.

The UDMS800 series includes multiple channels, which enables the use of several systems in the same venue without risk of interference. This is particularly important in conference situations or events where multiple speakers may be required.

Overall, the Bogen UDMS800HH and UDMS800BP are versatile, powerful, and reliable PA systems. With their thoughtful design, superior sound quality, and user-friendly features, they are an excellent choice for anyone needing effective audio solutions in a variety of professional settings.
Top Page Image Contents