UHT800 Handheld MIC Transmitter

1.Microphone Battery Installation

Install batteries by unscrewing the BATTERY COMPARTMENT COVER (29) counterclockwise and remove, exposing the BATTERY HOLDER (38). Insert two fresh AA ALKALINE BATTERIES (32), observing the correct polarity, and screw the cover back on to the microphone. Make sure the cover is screwed clockwise completely. Fresh alkaline batteries can last up to 10 hours in use, but in order to ensure optimum performance, it is recommended that you replace the batteries after every 7-8 hours of use.

2.Programming UHT800 to Selected Group/Channel (Frequency)

The transmitter must be programmed to the same frequency as selected for the receiver via automatic synchronization using the IR ASC™ Sync function. It can not be programmed on the transmitter itself. See “Selecting the Receiver Group/Channel and Programming” in next section. To manually IR program the receiver preselected frequency into the transmitter, place the transmitter’s IR RECEPTOR SENSOR WINDOW (37) 6-12” away from the receiver’s IR WINDOW (12). Press the MENU BUTTON (14) four times to the IR Screen then press the UP BUTTON (13) to start IR programming. This flashing IR INDICATOR (22) icon indicates IR transmission is in progress. When the synchronization is completed successfully, the RF INDICATOR (19) and the diversity A or B INDICATOR (20) on the receiver will show up. (See section on Selecting the Group/Channel (Frequency) and IR Programming for transmitters.)

(Note: If no button is pressed for a five second period during a selection, the program is terminated and the process needs to be repeated.)

3.Operating the UHT800 Handheld MIC Transmitter

Turn on the UHT800 by sliding the AUDIO MUTE (36) to the OFF position first. Then slide the POWER SWITCH (35) to the ON position. The TX LED INDICATOR (green) (33) will stay on to indicate that the transmitter is on. The LOW BATTERY INDICATOR LED (red) (34) will stay OFF, indicating usable-battery strength. In the case of a dead battery, the BATTERY INDICATOR LED (34) will stay on continuously, indicating that the batteries should be replaced. To preserve battery life, turn the transmitter off when not in use.

The microphone is now ready to use. The A or B DIVERSITY LED INDICATOR (20) on the UDR800 receiver should now be lit, indicating a received signal from the transmitter. When ready to speak, slide the AUDIO MUTE (36) to the ON position.

(Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that acoustic feedback (howling or screeching) will be avoided.)

(Note: The windscreen of the UHT800 functions as a built-in antenna.For proper operation, never remove the windscreen during use, or exchange with another type. For optimum range, maintain line-of-sight between the transmitter and the receiver whenever possible. Holding the microphone tightly, bridging across the windscreen and mic tube, will also lessen range. Hold MIC by the MIC tube housing only for optimum operation.)

For optimum performance, an AUDIO INPUT LEVEL (31) is provided. Adjust the gain by turning the control with a small screwdriver. It is recommended that the level be set at about 1/2 maximum. Experiment and set for maximum possible gain without audible distortion on the high level peaks.

(Note: Turning down the gain too much can compromise the signal-to-noise ratio, and is not recommended.)

UDMS800BP, UDMS800HH specifications

The Bogen UDMS800HH and UDMS800BP are advanced public address systems designed to deliver high-quality sound and reliable performance in various settings. These models are particularly favored in educational institutions, corporate environments, and large venues where effective communication is crucial.

The UDMS800HH features a handheld microphone that allows for mobility and flexibility during presentations or speeches. It utilizes UHF (Ultra High Frequency) technology, ensuring clear audio transmission over long distances with minimal interference. The handheld microphone is lightweight and ergonomically designed for comfortable use during extended periods. The microphone also incorporates a built-in rechargeable battery, providing convenience and reducing the need for constant battery replacements.

On the other hand, the UDMS800BP boasts a belt-pack transmitter, which is ideal for hands-free applications. This model is often paired with lavalier or headset microphones, making it perfect for teachers or presenters who need to move around while engaging their audience. The belt-pack design allows users to clip it onto their waist or belt, providing a wireless experience without the hassle of cords.

Both models are equipped with easy-to-use controls for volume adjustment, channel selection, and power on/off, making it user-friendly for novice and experienced operators alike. The systems feature a robust construction resistant to wear and tear, ensuring durability even in demanding environments.

Another significant characteristic is the wide frequency response and low distortion, which guarantee natural sound reproduction. Bogen's proprietary technologies enhance audio clarity, making them suitable for spoken word applications and musical performances alike.

The UDMS800 series includes multiple channels, which enables the use of several systems in the same venue without risk of interference. This is particularly important in conference situations or events where multiple speakers may be required.

Overall, the Bogen UDMS800HH and UDMS800BP are versatile, powerful, and reliable PA systems. With their thoughtful design, superior sound quality, and user-friendly features, they are an excellent choice for anyone needing effective audio solutions in a variety of professional settings.