JVC LYT0002-0A1A REC pg, Close the cassettes cover, Play pg, Don’t work, System Menu pg

Page 67

TROUBLESHOOTING 67

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer or Technical Service Center.

 

SYMPTOM

 

POSSIBLE CAUSES

 

CORRECTIVE ACTION

1.

No power is supplied.

1. •The power is not connected

 

1. •Connect the AC Adapter

 

 

 

properly.

 

securely (☞ pg. 10).

 

 

 

•The battery is dead.

 

•Replace the dead battery

 

 

 

•The LCD monitor is not

 

with a fully charged one

 

 

 

open fully when recording.

 

(☞ pg. 9).

 

 

 

 

 

•Open the LCD monitor

 

 

 

 

 

fully. The LCD monitor

 

 

 

 

 

turns on/off when it is

 

 

 

 

 

opened/closed while the

 

 

 

 

 

Power Dial is set to “REC”.

2.

Recording cannot be

2. •The tape’s record safety tab

 

2. •Set the tape’s record safety

 

performed.

is set to “SAVE”.

 

tab to “REC” (☞ pg. 13).

 

 

 

•The Power Dial is set to

 

•Set the Power Dial to

 

 

 

“PLAY”.

 

“REC” (☞ pg. 19).

 

 

 

•The cassette's cover is open.

 

•Close the cassette's cover.

3. There is no playback

3. •The camcorder is not getting

 

3. •Turn the camcorder’s power

 

picture.

power, or some other

 

off and on again (☞ pg. 19).

 

 

 

malfunction exists.

 

 

4. Some functions are not

4. •The shooting mode selector

 

4. •Set the shooting mode

 

available.

is set to “AUTO”.

 

selector to "MANUAL"

 

 

 

•The Power Dial is set to “5S”.

 

(☞ pg. 18).

 

 

 

 

 

•Set the Power Dial to any

 

 

 

 

 

position except “5S”

 

 

 

 

 

(☞ pg. 28).

5. The focus does not adjust

5. •Focus is set to “MANUAL”.

 

5. •Set Focus to “AUTO”

 

automatically.

•The recording was done in a

 

(☞ pg. 46).

 

 

 

dark place, or the contrast

 

•Clean the lens and check

 

 

 

was low.

 

the focus again (☞ pg. 72).

 

 

 

•The lens is dirty or covered

 

 

 

 

 

with condensation.

 

 

6. The cassette won’t load

6. •The cassette is in the wrong

 

6. •Set it in the right position

 

properly.

position.

 

(☞ pg. 13).

 

 

 

•The battery’s charge is low.

 

•Install a fully charged

 

 

 

 

 

battery (☞ pg. 8).

7.

Play, Rewind and

7. •The Power Dial is not set to

 

7. •Set the Power Dial to

 

Fast-Forward functions

“PLAY”.

 

“PLAY” (☞ pg. 49).

 

don’t work.

•The cassette’s cover is open.

 

•Close the cassette's cover

 

 

 

 

 

(☞ pg. 13).

8. The tape is moving, but

8. •The LCD monitor is turned

 

8. •Press and hold the IND/

 

there’s no picture.

off.

 

DISPLAY button for over 2

 

 

 

•Your TV has AV input

 

seconds (☞ pg. 23).

 

 

 

terminals, but is not set to

 

•Set the TV to the mode or

 

 

 

its VIDEO mode.

 

channel appropriate for

 

 

 

 

 

video playback (☞ pg. 53).

9.In the 5-Second mode, recording ends before 5 seconds have elapsed.

9. •The 5-Second mode in the

9. •Select “5S” or “5SD” in the

System Menu is set to

System Menu (☞ pg. 33).

“ANIMATION”.

CONTINUED ON NEXT PAGE

Page 66 Page 68
Image 67
Page 66 Page 68
Contents GR-DVM1 It is recommended that you Dear CustomerConnection to the mains supply in the United Kingdom Some DO’S and DON’TS on the Safe USE of Equipment Safety Precautions Video Area Audio Area Sub-Code AreaITI Insert and Tracking Information Area DC cord CAM Stand Sun hood Grip Hand strap Battery pack BN-V812UAUDIO/VIDEO cable Video cable ø Audio cable ø AA-V80EK or AA-V80EACD-ROM DV30MEDetach Charging The Battery PackDetach BATTERY/BATTERIES AttachClose Battery Cover Installing The Battery PackOpen Battery Cover Insert BatteryAttach to CAM Stand Using The CAM StandSupply Power Indoor UseReplace Battery Holder Clock Lithium Battery CR2025 Insertion/RemovalRemove OLD Battery Insert NEW BatteryOpen LCD Monitor Date/Time SettingsSelect Operation Mode Access Recording MenuTo protect valuable recordings Loading/Unloading a CassetteOpen Cassette Door INSERT/REMOVE TapeHand Strap Attachment Recording Mode SettingLens Cover Detachment Detach SUN Hood Sun Hood AttachmentAttach SUN Hood Open SUN HoodGrip Attachment Grip AdjustmentInstalling The Battery Remote Control UnitRE-INSERT Holder Full Auto/Manual Operation END Recording Turn on PowerBasic Recording Start RecordingStart Search Select ModeEngage Still Mode Recording From The Middle Of a TapePartway through the tape When blank portion is recorded on a tapeTime Code During shootingGrasp Camcorder Holding The CamcorderLCD Monitor Indications Adjust BrightnessBrightness Control Journalistic shootingInterface Shooting Zoom Take Snapshot Motor Drive modeChanging the Snapshot Setting SnapshotTo Stop a Snapshot Search In Progress Snapshot SearchRewind Tape Begin SearchTo Take a Snapshot In The 5-Second Mode Press the PUSH-OPENswitch and open the LCD monitor fullyScene To Take a Snapshot In The Self-Timer Mode Self-Timer, press Snapshot instead Press MENU. The Recording Menu appears in the LCD monitor MenusSelect Function Close Recording MenuZoom Magnification DIS Digital Image StabilizerSystem Menu Access System MenuClose System Menu END SET Menu Button Sound signals can be sampled at 32 kHz or 48 kHzSelect Effect FADE/WIPE EffectsFades and Wipes Press Recording START/STOP Picture Wipe/DissolveResume Recording Dissolve? R Random Fader Random VariationsClose Menu Accessmenu FADER/WIPE CustomizeExchanging FADE/WIPE Effects Select NEW EffectFades and Wipes Refer to page 34 on using the exchanged effectsAE/Effects Disable P.AE/EFFECTTwilight √ Monotone √Video Echo Sepia √ Classic Film √Exchanging P.AE/Effects Accessmenu P.AE/EFFECT CustomizeDisplaying The Date And Time During Recording Select Auto in . Or set the shooting Mode selector to Auto White Balance AdjustmentTo Return To Automatic White Balance To Change The Tint For Recording Enter SettingManual White Balance Operation Exit Recording MenuAdjust Focus Manual Focus AdjustmentTo Change To Auto Focus To Return To Automatic Exposure Control Adjust ExposureExposure Control Brightness control of the LCD monitorIris Iris LockYou can watch what you’ve recorded in the LCD monitor Viewing RecordingEND Playback To Perform High-Speed SearchPress 46. You can watch the scenes you recorded on the TV VCR/TV ConnectionStart Playback Recording deckDocking Station Attachment Confirm POWER-OFF StatusAttach and Locks Recorder or a TV with a Input connectorTV Playback Connection to an S-VHSConnect as shown in the illustration pg Turn on Power Select TV’S Video ModeConnect Docking Station to TV or VCR Connectinput VCR Output to TV Start PlaybackPress Menu again, and the menu disappears Access Playback MenuPlayback Menu To set parameters for other functions, repeat steps 3Displaying the Date During Playback Playback SoundDisplaying The Time Code During Playback END Zoom Playback ZoomActivate Zoom Locatescene Portion of MagnifiedPress Play Playback EffectsRM-V708U or WRM-V710U provided Pause Recording Docking StationDubbing Make ConnectionsOperate the VCR Brand SettingRM-V708U or RM-V710U 9 ` provided Execute FADE/WIPE in if Necessary To Operate The VCR With The Remote ControlRandom Assemble Editing Start Source Playback if NecessaryUSE P.AE/EFFECT if Necessary SET EDIT-IN PointSET EDIT-OUT Point USE Fade Wipe on Scene TRANSI- Tion if NecessaryStart Editing Engagemode Vcrs RECORD-PAUSEStop Editing RM-V708U or For More Accurate EditingPrepare for R.A. Edit Play Back Dubbed Scene Choose a ScenePress MENU. The Playback Menu appears on the TV screen Input Correction DataNow perform Random Assemble Editing beginning with on Pause During Dubbing Audio DubbingFind EDIT-IN Point Begin DubbingPrepare for Insert Editing Stop Editing Insert EditingFind Edit OUT Point Start Recording Find Edit in Point Pause During EditingPlay pg 5-Second mode Select 5S or 5SDREC pg Close the cassettes coverTR Ouble Shooting Picture Wipe function doesn’t work Squeeze or Cinema mode is selected in the Recording MenuPossible Causes This may occur when Cleaning The Camcorder Main Unit Name & Function LCD Monitor Indications During RecordingLCD Monitor Indications During Playback Jlip Video Capture Docking Station To prevent damage to the camcorder For safety, do notAvoid using the unit To avoid hazardTo prevent damage to the LCD monitor, do not To prolong service lifeDo not leave the unit To protect the unit, do notVideo signal recording format PowerPower consumption Format Signal formatWeight Approx g with battery installed Power V/1,250mAh DimensionsWeight Approx g Power DC 3 V Lithium Battery CR2025 Battery LifeOn-screen display Colour temperatureAC Adapter Auto focusPlay Back on TV Motor Drive ModeAnimation Audio Dubbing Connections Pgs , 50Page GR-DVM1

LYT0002-0A1A specifications

The JVC LYT0002-0A1A is a cutting-edge camera accessory designed specifically for enhancing video and imaging capabilities. Aimed at both amateur and professional videographers, this product incorporates various advanced features and technologies to facilitate exceptional video capture and improved functionality.

One of the key features of the LYT0002-0A1A is its high compatibility with a range of JVC camcorders. This ensures seamless integration and allows users to leverage its full potential without needing extensive adjustments or additional equipment. The accessory is built with precision, enhancing the overall filming experience by providing stability and versatility.

Another significant characteristic of the LYT0002-0A1A is its lightweight and compact design. Weighing in at just a few ounces, it allows for easy transport and setup, ensuring that users can take it anywhere without the hassle of heavy equipment. This makes it ideal for on-the-go filming, whether for professional projects or personal content creation.

In terms of technology, the LYT0002-0A1A boasts impressive stabilization capabilities. The in-built stabilization technology minimizes shake and vibrations, resulting in smoother footage even in challenging shooting conditions. This feature is especially beneficial for action shots or outdoor filming where movement is unavoidable.

The user-friendly interface of the LYT0002-0A1A should not be overlooked. Designed with the end-user in mind, it incorporates intuitive controls that provide quick access to essential functions, making it suitable for beginners and experienced users alike. This simplicity enhances the overall user experience, allowing for more focus on creativity rather than on technical adjustments.

Additionally, the LYT0002-0A1A supports high-resolution video recording, which is crucial for producing high-quality content. Its ability to capture sharp, detailed images ensures that users can produce professional-grade videos that stand out in an increasingly competitive digital landscape.

Overall, the JVC LYT0002-0A1A is a remarkable camera accessory that combines cutting-edge technology with user-friendly design. Its main features, including compatibility with JVC camcorders, lightweight construction, advanced stabilization, and high-resolution recording, make it an essential tool for anyone serious about videography. This accessory not only enhances video quality but also simplifies the filming process, allowing users to focus on their creativity and storytelling.
Top Page Image Contents