Panasonic NV-GS75GN operating instructions Setting date and time, Adjusting LCD monitor/viewfinder

Page 15

Before using

3Press the [MENU] button to exit the menu screen.

VAR.

SEARCHMENU

ENTER

Setting date and time

If the screen shows the incorrect date/time, then adjust it.

Set to Tape Recording Mode or Card

Recording Mode.

1Set [BASIC] >> [CLOCK SET] >> [YES].

2Move the joystick left or right in order to select the item to be set. Then move the joystick up or down to set the desired value.

The year will change as follows: 2000, 2001, ..., 2089, 2000, ...

The 24-hour clock is used.

3Press the joystick to determine the setting.

The clock function starts at [00] seconds.

ªAbout date/time

The date and time function are driven by a built- in lithium battery.

Make sure to check the time before recording because the built-in clock is not very accurate.

ªRecharging the built-in lithium battery

If [0] or [--] is indicated when the camera is turned on, then the built-in lithium battery runs down. Connect the AC adaptor to the camera or place the battery on the camera, and the built-in lithium battery will be recharged. Leave the camera as is for approx. 24 hours, and the battery will drive the date and time for approx. 6 months. (Even if the [OFF/ON] switch is set to [OFF], the battery is still being recharged.)

WARNING

THE LITHIUM BATTERY IN THIS UNIT MUST ONLY BE REPLACED BY QUALIFIED PERSONNEL. IF THIS IS NECESSARY, CONTACT THE PANASONIC CUSTOMER CARE CENTRE ON 132600 FOR YOUR NEAREST AUTHORIZED SERVICE CENTRE.

Adjusting LCD monitor/viewfinder

ªAdjusting the brightness and colour

level

1Set [SETUP] >> [LCD SET] or [EVF SET] >> [YES].

2Move the joystick up or down in order to select the item to be adjusted.

[LCD SET]

:Brightness of the LCD monitor

:Colour level of the LCD monitor [EVF SET]

EVF :Brightness of the viewfinder

3Move the joystick left or right to move the bar indication representing the brightness.

4Press the [MENU] button or the joystick to complete the settings.

In order to adjust the brightness of the viewfinder, close the LCD monitor, and the

viewfinder will be activated.

When the LCD monitor is rotated by 180° towards the lens, the brightness of the LCD monitor cannot be adjusted.

These settings will not affect the images actually recorded.

ªIn order to increase the brightness of

the entire LCD monitor

1Press the [POWER LCD] button.

POWER LCD

The [POWER LCD] lamp lights up.

If the [POWER LCD] button is pressed, the entire LCD monitor will become approx. twice as bright as the normal.

Press this button again, and the lamp will go off and the brightness will revert back to the original brightness.

This will not affect the images to be recorded.

If you turn on the camera when the AC adaptor is used, the [POWER LCD] function will automatically be activated.

15

VQT0N61

Image 15
Contents Operating Instructions Information for your safety Contents Parts identification and handling Before usingAccessories OptionalTripod receptacle Viewfinder -8Fitting the lens cap Shoulder strap fixtureLens hood To use as a hand strap Using the LCD monitorTo restore the strap to the grip belt One-touch free-style grip beltPower supply Using the viewfinderConnect the DC input lead to this product Fitting the batteryRemoving the battery Charging time and recordable timeInserting/removing the cassette When the cassette holder does not Come outWhen the cassette holder cannot be Housed Inserting/removing a cassetteSD Memory Card Card access lampInserting/removing a card Concerning the cardSelecting a mode How to use the joystickTurning the camera on Joystick and screen display Tape recording mode AUTO/MANUAL/FOCUS switch is set to AutoCard recording mode AUTO/MANUAL/FOCUS switch is set to Auto Tele-macro Soft skin mode Backlight compensationUsing the menu screen Switching the languageAdjusting LCD monitor/viewfinder Setting date and timeRemote control usable range Using the remote controlRemote control Install a button-type batteryConnect the free style remote control To the camera Free style remote controlSelecting the remote control mode Concerning the button-type batteryCheck before recording Record modeOn-screen display in the tape recording mode Recording on a tapeConcerning the remaining tape time Indication on the screen Stopping blank search midway Through Check the recordingBlank search function Recording still pictures onto a card PhotoshotZoom in/out function To use the zoom microphone function To cancel the quick start when Power is OFFRecording yourself Quick startTo return to normal recording To cancel the colour night view functionBacklight compensation function Night view functionsSoft skin mode Tele-macro functionFade in/fade out function Self-timer recording Wind noise reduction functionRecording images for wide-screen TVs Continuous Photoshot To cancel the image stabilizer function≥Set to Tape Recording Mode Set Advance SIS on Image stabilizer functionTo cancel the scene mode function Recording in various situations Scene modeRecording in natural colours White balance Manual focus adjustment Manual shutter speed/aperture adjustmentTo restore to automatic adjustment Iris/gain value range Manual iris/gain adjustment50-1/8000 seconds Tape Recording Mode Shutter speed rangePlaying back tape Playback modeTo adjust volume Settings on the audioSlow-motion playback/ frame-by-frame playback Variable-speed search functionTo return to normal playback Playback on TV Playing back cardTo display the on-screen information On the TV To delete all files Deleting files recorded on a cardTo display multiple playback files About the compatibility of still picturesProtecting files on a card Writing the printing data on a card Dpof settingTo complete the settings Formatting a cardWhat is DPOF? Select Cancel ALL in StepTo set so that all pictures are not Printed Edit mode Recording from a tape onto a cardCopying onto a DVD recorder or a VCR Dubbing To cancel the standby for recording Using the DV Cable for Recording Digital DubbingTo dub audio while listening to a Pre-recorded sound Audio dubbingBefore recording with audio dubbing To play back the sound recorded with Audio dubbingWhen you stop printing halfway Tape Playback Menu MenuMenu list Tape Recording MenuCard Recording Menu Picture Playback MenuBasic DATE/TIME -43-PROTECT Menus related to playback Menus related to taking picturesDemo Mode Other menusInitial SET Indications OthersTextual indications Confirmatory indicationsCheck the connected printer Functions cannot be used simultaneouslyThere is no ink. Check the connected printer There is no paper. Check the connected printerMovie camera power does not stay on long enough Before requesting repair Problems and solutionsPower/Body Movie camera power cannot be turned on Movie camera power is turned off automaticallyScreen has changed suddenly Remote control does not functionCassette cannot be removed No operation other than cassette removal can be performedSounds cannot be played back Original sound was erased when audio dubbing was performedDifferent sounds are reproduced at the same time Audio dubbing cannot be performedAbout condensation About the movie camera About dirty headsDo not throw old battery into fire About the batteryBe sure to detach the battery after use Prepare spare batteries when going out for recordingFolder structure of the card About the AC adaptorAbout the cassette About the cardViewfinder Explanation of termsPeriodical check-ups Automatic white balanceAuto focus White balanceHttp//panasonic.co.jp/pavc/global/cs SpecificationsSpecifications SpecificationsAC adaptor VQT0N61 S0105Ke0