Panasonic NV-GS150GN Setting date and time, Adjusting LCD monitor/viewfinder

Page 15

Before using

VAR.

SEARCHMENU

ENTER

3Press the [MENU] button to exit the menu screen.

VAR.

SEARCHMENU

ENTER

Setting date and time

If the screen shows the incorrect date/time, then adjust it.

≥Set to Tape Recording Mode or Card

Recording Mode.

1Set [BASIC] >> [CLOCK SET] >> [YES].

2Move the joystick left or right in order to select the item to be set. Then move the joystick up or down to set the desired value.

≥The year will change as follows: 2000, 2001, ..., 2089, 2000, ...

≥The 24-hour clock is used.

3Press the joystick to determine the setting.

≥The clock function starts at [00] seconds.

ªAbout date/time

≥The date and time function are driven by a built- in lithium battery.

≥Make sure to check the time before recording because the built-in clock is not very accurate.

ªRecharging the built-in lithium battery

≥If [0] or [--] is indicated when the camera is turned on, then the built-in lithium battery runs down. Connect the AC adaptor to the camera or place the battery on the camera, and the built-in lithium battery will be recharged. Leave the camera as is for approx. 24 hours, and the battery will drive the date and time for approx. 6 months. (Even if the [OFF/ON] switch is set to [OFF], the battery is still being recharged.)

WARNING

THE LITHIUM BATTERY IN THIS UNIT MUST ONLY BE REPLACED BY QUALIFIED PERSONNEL. IF THIS IS NECESSARY, CONTACT THE PANASONIC CUSTOMER CARE CENTRE ON 132600 FOR YOUR NEAREST AUTHORIZED SERVICE CENTRE.

Adjusting LCD monitor/viewfinder

ªAdjusting the brightness and colour

level

1Set [SETUP] >> [LCD SET] or [EVF SET] >> [YES].

2Move the joystick up or down in order to

select the item to be adjusted. [LCD SET]

:Brightness of the LCD monitor

:Colour level of the LCD monitor [EVF SET]

EVF :Brightness of the viewfinder

3Move the joystick left or right to move the bar indication representing the brightness.

4Press the [MENU] button or the joystick to complete the settings.

≥In order to adjust the brightness of the viewfinder, close the LCD monitor, and the viewfinder will be activated.

≥When the LCD monitor is rotated by 180° towards the lens, the brightness of the LCD monitor cannot be adjusted.

≥These settings will not affect the images actually recorded.

ªIn order to increase the brightness of

the entire LCD monitor

1Press the [POWER LCD] button.

POWER LCD

≥The [POWER LCD] lamp lights up.

15

VQT0N50

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operating Instructions Information for your safety Contents Optional Before usingAccessories Parts identification and handlingViewfinder -8 LCD monitor open part Open Smart accessory shoeShoulder strap fixture Lens hood Tripod receptacleTo use as a hand strap To restore the strap to the grip beltFitting the lens cap optional One-touch free-style grip beltUsing the LCD monitor Using the viewfinderPower supply Charging time and recordable time Connecting to the AC outletFitting the battery Removing the batteryInserting/removing the cassette When the cassette holder does not Come outWhen the cassette holder cannot be Housed Inserting/removing a cassetteSD Memory Card Card access lampInserting/removing a card Concerning the cardTurning the camera on Using the lens coverSelecting a mode How to use the joystickJoystick and screen display Tape recording mode AUTO/MANUAL/FOCUS switch is set to AutoTape playback mode Card recording mode AUTO/MANUAL/FOCUS switch is set to AutoUsing the menu screen Switching the languageAdjusting LCD monitor/viewfinder Setting date and timeChanging the picture quality on LCD monitor Using the remote controlRemote control Set Setup LCD AI Dynamic orConcerning the button-type battery Install a button-type batteryRemote control usable range Selecting the remote control modeFree style remote control with mic Switching the microphoneAbout the clip on the backside Check before recording Record modeOn-screen display in the tape recording mode Recording on a tapeConcerning the remaining tape time Indication on the screen Stopping blank search midway Through Check the recordingBlank search function Recording still pictures onto a card PhotoshotSelect the size of still pictures to be Recorded on a card On-screen display in the card recording modeConcerning the focusing area Progressive PhotoshotTo use the zoom microphone function Zoom in/out functionRecording yourself Digital zoom functionNight view functions To cancel the quick start when Power is OFFQuick start Backlight compensation functionTo cancel the tele-macro function Soft skin modeTo cancel the colour night view function To cancel the soft skin modeUsing the built-in video flash Fade in/fade out functionWind noise reduction function Self-timer recording Image stabilizer function To cancel the Wide/Cinema functionTo cancel the image stabilizer function Recording images for wide-screen TVsTo stop continuous photoshot Midway through Recording in various situations Scene modeTo cancel the scene mode function Continuous PhotoshotRecording in natural colours White balance Manual focus adjustment Manual shutter speed/aperture adjustmentTo restore to automatic adjustment Manual iris/gain adjustment Shutter speed rangeIris/gain value range Playback mode Playing back tapeSlow-motion playback/ frame-by-frame playback Frame-by-frame playback Variable-speed search functionPlayback on TV To return to normal playbackAbout the compatibility of still pictures Playing back cardTo display the on-screen information On the TV To display multiple playback filesProtecting files on a card To complete the settingsDeleting files recorded on a card Formatting a cardWriting the printing data on a card Dpof setting What is DPOF?To set so that all pictures are not Printed Edit mode Recording from a tape onto a cardCopying onto a DVD recorder or a VCR Dubbing To cancel the standby for recording Using the DV Cable for Recording Digital DubbingTo play back the sound recorded with Audio dubbing ≥Set to Tape Playback ModeAudio dubbing Before recording with audio dubbingWhen you stop printing halfway Tape Playback Menu MenuMenu list Tape Recording MenuPicture Playback Menu SetupSetup Display -44-REMOTE Card Recording MenuMenus related to playback Menus related to taking picturesDemo Mode Other menusInitial SET Indications OthersTextual indications Confirmatory indicationsChange Aspect to Functions cannot be used simultaneouslyMovie camera power does not stay on long enough Before requesting repair Problems and solutionsPower/Body Movie camera power cannot be turned on Movie camera power is turned off automaticallyRecording Remote control does not functionCassette cannot be removed No operation other than cassette removal can be performedSounds cannot be played back Original sound was erased when audio dubbing was performedDifferent sounds are reproduced at the same time Audio dubbing cannot be performedAbout condensation About the movie camera When 3 in redWhen the lens is fogged About dirty headsAbout the battery Folder structure of the card About the AC adaptorAbout the cassette About the cardWhite balance Explanation of termsPeriodical check-ups Automatic white balanceRecording a fast-moving subject Auto focusRecording a subject behind dirty or dusty glass Recording a subject in dark surroundingsSpecifications SpecificationsAC adaptor VQT0N50
Top Page Image Contents