Panasonic NV-GS150GN Install a button-type battery, Remote control usable range

Page 17

Before using

(14)Recording start/stop button [START/STOP] ¢

(15)Playback button [1]

(16)Fast forward/cue button [5]

(17)Enter button [ENTER] -14-

¢means that these buttons function in the same manner as the corresponding buttons on the movie camera.

ªInstall a button-type battery

Install the button-type battery supplied in the remote control before using it.

1While pressing the stopper 1, pull out the battery holder.

1

2Set the button-type battery with its (i) mark facing upward and get the battery holder back in place.

Caution

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.

Warning

Risk of fire, explosion and burns. Do not recharge, disassemble, heat above 100xC or incinerate. Keep the Button-Type battery out of the reach of children. Never put Button- Type battery in mouth. If swallowed call your doctor.

ªRemote control usable range

The distance between the remote control and the camera: Within approx. 5 m

Angle: Approx. 10o up and 15o down, left, and right

ªSelecting the remote control mode

If 2 cameras are used simultaneously, set the mode for one pair of movie camera and remote control to [VCR1] and that of the other pair to [VCR2]. This will prevent interference between the 2 pairs. (The default setting is [VCR1]. When the button-type battery is replaced, the setting will revert to the default [VCR1].)

1 Setting on the camera:

Set [SETUP] >> [REMOTE] >> [VCR1] or [VCR2].

2 Setting on the remote control:

STILL ADV PAUSE STILL ADV

VOL

2

1

 

STOP

VAR

[VCR1]:

Press [D] and [] simultaneously. 1 [VCR2]:

Press [E] and [] simultaneously. 2

ªConcerning the button-type battery

When the button-type battery runs down, replace it with a new battery (part number: CR2025). The battery is normally expected to last about 1 year, but it depends on operation frequency.

Keep the button-type battery out of the reach of children.

If the remote control mode of the camera and that of the remote control do not match with each other, “REMOTE” will appear. When the remote control is operated for the first time after the camera is turned on, “CHECK REMOTE MODE” (-47-) will appear and operation is impossible. Set the same remote control mode.

The remote control is intended for indoor operation. Outdoors or under strong light, the movie camera may not operate properly even within the usable ranges.

Within a 1 metre range, you can operate the remote control from beside the remote control sensor (LCD monitor side) of the movie camera.

17

VQT0N50

Image 17
Contents Operating Instructions Information for your safety Contents Accessories Before usingParts identification and handling OptionalViewfinder -8 LCD monitor open part Open Smart accessory shoeShoulder strap fixture Lens hood Tripod receptacleFitting the lens cap optional To restore the strap to the grip beltOne-touch free-style grip belt To use as a hand strapPower supply Using the LCD monitorUsing the viewfinder Fitting the battery Connecting to the AC outletRemoving the battery Charging time and recordable timeWhen the cassette holder cannot be Housed When the cassette holder does not Come outInserting/removing a cassette Inserting/removing the cassetteInserting/removing a card Card access lampConcerning the card SD Memory CardSelecting a mode Using the lens coverHow to use the joystick Turning the camera onTape playback mode Tape recording mode AUTO/MANUAL/FOCUS switch is set to AutoCard recording mode AUTO/MANUAL/FOCUS switch is set to Auto Joystick and screen displayUsing the menu screen Switching the languageAdjusting LCD monitor/viewfinder Setting date and timeRemote control Using the remote controlSet Setup LCD AI Dynamic or Changing the picture quality on LCD monitorRemote control usable range Install a button-type batterySelecting the remote control mode Concerning the button-type batteryAbout the clip on the backside Free style remote control with micSwitching the microphone Check before recording Record modeConcerning the remaining tape time Indication on the screen On-screen display in the tape recording modeRecording on a tape Blank search function Check the recordingRecording still pictures onto a card Photoshot Stopping blank search midway ThroughConcerning the focusing area On-screen display in the card recording modeProgressive Photoshot Select the size of still pictures to be Recorded on a cardRecording yourself Zoom in/out functionDigital zoom function To use the zoom microphone functionQuick start To cancel the quick start when Power is OFFBacklight compensation function Night view functionsTo cancel the colour night view function Soft skin modeTo cancel the soft skin mode To cancel the tele-macro functionWind noise reduction function Using the built-in video flashFade in/fade out function Self-timer recording To cancel the image stabilizer function To cancel the Wide/Cinema functionRecording images for wide-screen TVs Image stabilizer functionTo cancel the scene mode function Recording in various situations Scene modeContinuous Photoshot To stop continuous photoshot Midway throughRecording in natural colours White balance To restore to automatic adjustment Manual focus adjustmentManual shutter speed/aperture adjustment Iris/gain value range Manual iris/gain adjustmentShutter speed range Slow-motion playback/ frame-by-frame playback Playback modePlaying back tape Playback on TV Variable-speed search functionTo return to normal playback Frame-by-frame playbackTo display the on-screen information On the TV Playing back cardTo display multiple playback files About the compatibility of still picturesDeleting files recorded on a card To complete the settingsFormatting a card Protecting files on a cardTo set so that all pictures are not Printed Writing the printing data on a card Dpof settingWhat is DPOF? Copying onto a DVD recorder or a VCR Dubbing Edit modeRecording from a tape onto a card To cancel the standby for recording Using the DV Cable for Recording Digital DubbingAudio dubbing ≥Set to Tape Playback ModeBefore recording with audio dubbing To play back the sound recorded with Audio dubbingWhen you stop printing halfway Menu list MenuTape Recording Menu Tape Playback MenuSetup Display -44-REMOTE SetupCard Recording Menu Picture Playback MenuMenus related to playback Menus related to taking picturesInitial SET Demo ModeOther menus Indications OthersTextual indications Confirmatory indicationsChange Aspect to Functions cannot be used simultaneouslyPower/Body Movie camera power cannot be turned on Before requesting repair Problems and solutionsMovie camera power is turned off automatically Movie camera power does not stay on long enoughCassette cannot be removed Remote control does not functionNo operation other than cassette removal can be performed RecordingDifferent sounds are reproduced at the same time Original sound was erased when audio dubbing was performedAudio dubbing cannot be performed Sounds cannot be played backAbout condensation When the lens is fogged When 3 in redAbout dirty heads About the movie cameraAbout the battery About the cassette About the AC adaptorAbout the card Folder structure of the cardPeriodical check-ups Explanation of termsAutomatic white balance White balanceRecording a subject behind dirty or dusty glass Auto focusRecording a subject in dark surroundings Recording a fast-moving subjectSpecifications SpecificationsAC adaptor VQT0N50