Axis Communications P3215-VE user manual UPnPTM, RTP/H.264, Bonjour

Page 44

AXIS P3215-VE Network Camera

System Options

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 37. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 48.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

44

Image 44
Contents Axis P3215-VE Network Camera About this document Legal ConsiderationsLiability Intellectual Property RightsSupport Learn MoreTable of Contents Axis P3215-VE Network CameraPerformance Considerations Connectors and Buttons Network ConnectorHardware Overview SD Card SlotLED Indicators Color IndicationAccess the Product Access from a BrowserAccess from the Internet Set the Root PasswordSet Power Line Frequency Camera OrientationLive View Click Use HttpsGo to Setup Events Controls on the Live ViewAxis Media Control viewer toolbar Manual TriggerPTZ Controls Axis Media Control AMC How to Stream H.264Media Streams Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P3215-VE Network Camera Set Up the Product Basic SetupWhen satisfied, click Enable iris to enable the iris Focus & ZoomVideo Video StreamPixel Counter Image264 Click Save to apply the new settingsStream Profiles Camera Settings Exposure SettingsImage Appearance White BalanceIris adjustment Shutter & GainSet Shutter to Day/NightSelect an Aspect ratio and a Video stream resolution View AreaOverlay Go to Video View AreaGo to Video Overlay Image Overlay ImageUse Overlay Text in an Action Rule Go to Events Action Rules Privacy MaskCreate the action rule Configure the Live View Default Viewer for BrowsersViewer Settings Browser Viewer DescriptionUser Defined Links Preset Positions Go to PTZ Preset PositionsPTZ Pan Tilt Zoom Guard TourControls AdvancedControl Queue Detectors Camera TamperingMotion Detection Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P3215-VE Network Camera Install Application Go to Setup ApplicationsApplications Application LicensesAxis P3215-VE Network Camera Setting Up an Action Rule EventsAdd Recipients Go to Events Action Rules and click AddSet Up Recurrences Set Up Email RecipientsCreate Schedules Go to Events Schedules and click AddAxis P3215-VE Network Camera Recordings Recording ListContinuous Recording Go to Recordings ListLanguages System Options SecurityUsers IP Address FilterGo to System Options Security Ieee IeeeCertificates Basic TCP/IP Settings Go to Setup System Options Security CertificatesDate & Time NetworkIPv4 Address Configuration IPv6 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAdvanced TCP/IP Settings Axis Internet Dynamic DNS ServiceAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationNTP Configuration Host Name ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service FTPUPnPTM can be disabled under System Options Network UPnPTM UPnPTMRTP/H.264 BonjourStorage SD CardMount and Unmount SD Card Format SD CardMaintenance Network ShareTo add a network share Go to System Options Storage Click Network ShareSupport Support OverviewSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigScripting File UploadTroubleshooting Upgrade the FirmwareEmergency Recovery Procedure Check the FirmwareSymptoms, Possible Causes and Remedial Actions Problems setting the IP addressProduct cannot be accessed from a browser Product is accessible locally but not externallyProblems with streaming H.264 Video and image problems, generalVideo Camera Settings Key framesStorage and disk management problems Storage disruptionRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Function/group Specifications System Application InstallationMaintenance General Casing Memory PowerConnectors Performance ConsiderationsM2.2