Axis Communications P1428-E user manual UPnPTM, RTP/H.264, Bonjour

Page 46

AXIS P1428–E Network Camera

System Options

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

Note

All AXIS Video MIB traps are enabled when SNMP v1/v2c traps are enabled. It is not possible to turn on or off specific traps.

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 39. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 50.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

46

Image 46

Contents Axis P1428-E Network Camera Liability About this DocumentLegal Considerations Intellectual Property RightsSupport Learn MoreTable of Contents Axis P1428-E Network CameraConnectors Performance Considerations Connector Connectors and ButtonsNetwork Connector Hardware OverviewControl Button LED IndicatorsSD Card Slot Color IndicationAccess from the Internet Access the ProductAccess from a Browser Set the Root PasswordControls on the Live View Set Power Line FrequencyLive View Click Use HttpsPTZ Controls Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerAxis P1428-E Network Camera Media Streams How to Stream H.264Axis Media Control AMC Alternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAxis P1428-E Network Camera Set Up the Product Basic SetupPixel Counter VideoVideo Stream ImageStream Profiles 264Image Appearance Camera SettingsExposure Settings White BalanceView Area Iris adjustmentSelect an Aspect ratio and a Video stream resolution Day/NightGo to Video Video Stream and select the Image tab OverlayOverlay Image Go to Video Overlay ImageUse Overlay Text in an Action Rule Go to Events Action RulesFocus & Zoom When satisfied, click Enable iris to enable the irisPrivacy Mask Go to Video Focus & ZoomViewer Settings Configure the Live ViewDefault Viewer for Browsers Browser Viewer DescriptionOutput Buttons Go to Setup Live View ConfigUser Defined Links For more information about I/O ports, see I/O Ports onGuard Tour Preset PositionsPTZ Pan Tilt Zoom AdvancedControl Queue Motion Detection DetectorsCamera Tampering Go to Detectors Camera TamperingSet Up Motion Detection Windows Motion Detection ParametersAxis P1428-E Network Camera Applications Install ApplicationGo to Setup Applications Application LicensesAxis P1428-E Network Camera Convert Event Types to Action Rules Set Up Action RulesEvents Go to Events Action Rules and click AddTriggers Actions Add RecipientsRecipient Types Create Schedules Set Up Email RecipientsGo to Events Schedules and click Add Set Up Recurrences Go to Events Recurrences and click AddContinuous Recording RecordingsRecording List Go to Recordings ListLanguages Users System OptionsSecurity IP Address FilterCertificates IeeeGo to System Options Security Ieee Date & Time Basic TCP/IP SettingsGo to Setup System Options Security Certificates NetworkAssign IP Address Using ARP/Ping IPv4 Address ConfigurationIPv6 Address Configuration ARP/PingAxis Internet Dynamic DNS Service requires IPv4 Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service DNS ConfigurationLink-Local IPv4 Address NTP ConfigurationHost Name Configuration NAT traversal port mapping for IPv4QoS Quality of Service FTPRTP/H.264 UPnPTM can be disabled under System Options Network UPnPTMUPnPTM BonjourNetwork Share StorageSD Card To add a network sharePorts & Devices MaintenanceSupport Scripting System OverviewLogs & Reports File UploadReset to Factory Default Settings Plain ConfigEmergency Recovery Procedure TroubleshootingUpgrade the Firmware Check the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externallyVideo Camera Settings Problems with streaming H.264Video and image problems, general Key framesRe-mount the storage device Storage and disk management problemsStorage disruption Reformat the SD card and then click MountTechnical Specifications Connectors Function/group Specifications Event actionsPower DimensionsConnectors Function Pin SpecificationsPerformance Considerations M2.3