Axis Communications M3007PV user manual Storage, UPnPTM, RTP/H.264, Bonjour, SD Card

Page 49

AXIS M3007–PV

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

Cold start

Warm start

Link up

Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 42. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 53.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

SD Card

NOTICE

To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.

Note

For SD card recommendations see www.axis.com

49

Image 49
Contents Axis M3007-PV Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis M3007-PV Table of ContentsPerformance Considerations Network Connector Connectors and ButtonsFor technical specifications, see RJ45 Ethernet connector with Power over Ethernet PoESD Card Slot LED IndicatorsControl Button Status LED IndicationAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordCamera Orientation Set Power Line FrequencyLive View Click Use HttpsControls on the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerPTZ Controls Media Streams How to Stream H.264Axis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M3007-PV Basic Setup Set Up the ProductVideo Set Up Video StreamsPixel Counter View modesPanorama OverviewDouble Panorama Quad View ImageDirection Click Save to apply the new settings264 Stream Profiles Camera SettingsImage Appearance White Balance Exposure SettingsWide Dynamic Range Shutter & GainView areas Date/Time Formats in the online help To enable overlaysOverlay Go to Video Video Stream and select the Image tabUse Overlay Text in an Action Rule Overlay ImageGo to Video Overlay Image Go to Events Action Rules Privacy MaskDefault Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links PTZ Pan Tilt Zoom Preset PositionsGuard Tour Controls AdvancedTo add a guard tour Go to PTZ Guard Tour and click AddCamera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis M3007-PV Go to Setup Applications Install ApplicationApplications Application LicensesAxis M3007-PV Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers Actions Add RecipientsRecipient Types Create Schedules Set Up Email RecipientsGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesRecording List RecordingsContinuous Recording Go to Recordings ListClick Save to save and start the recording Languages Security System OptionsUsers IP Address FilterCertificates IeeeGo to System Options Security Ieee Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM StorageRTP/H.264 BonjourFormat SD Card Mount and Unmount SD CardNetwork Share MaintenanceTo add a network share Go to System Options Storage Click Network ShareSupport Overview SupportSystem Overview Logs & ReportsPlain Config Reset to Factory Default SettingsFile Upload Upgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyVideo and image problems, general Problems with streaming H.264Video Camera Settings Key framesStorage disruption Storage and disk management problemsRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Maintenance Built-in Function/group Specifications System ApplicationInstallation aids Data Streaming PowerPerformance Considerations ConnectorsAxis M3007-PV