Axis Communications M1103 user manual Storage, UPnPTM, RTP/H.264, Bonjour, Network Share

Page 45

AXIS M1103

System Options

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 38. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 48.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

Storage

Network Share

Network share allows you to add network storage such as a NAS (network-attached storage). The NAS shall be dedicated for recordings and data from the Axis products connected to the network. For information about reference NAS devices, go to www.axis.com/products/cam_companion_software/supported.htm

Note

For NAS recommendations see www.axis.com

45

Image 45

Contents Axis M1103 Legal Considerations About this DocumentLiability Intellectual Property RightsLearn More SupportAxis M1103 Table of ContentsPerformance Considerations Network Connector Connectors and ButtonsHardware Overview Control ButtonPower LED Indication LED IndicatorsStatus LED Indication Network LED IndicationAccess from a Browser Access the ProductAccess from the Internet Set the Root PasswordSet Power Line Frequency Live ViewClick Create self-signed certificate Controls on the Live View Go to Setup EventsAxis Media Control viewer toolbar Manual TriggerPTZ Controls How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamAxis M1103 Basic Setup Set Up the ProductFocus Adjustment Back Focus AdjustmentVideo Stream VideoPixel Counter ImageClick Save to apply the new settings Stream Profiles264 Exposure Settings Camera SettingsView Area Image AppearanceOverlay Image OverlayGo to Video Video Stream and select the Image tab Go to Video Overlay ImageGo to Events Action Rules Use Overlay Text in an Action RulePrivacy Mask Default Viewer for Browsers Configure the Live ViewViewer Settings Browser Viewer DescriptionUser Defined Links Preset Positions PTZ Pan Tilt ZoomGuard Tour Controls AdvancedCamera Tampering DetectorsMotion Detection Go to Detectors Camera TamperingMotion Detection Parameters Set Up Motion Detection WindowsAxis M1103 Go to Setup Applications Install ApplicationApplications Application LicensesAxis M1103 Events Set Up Action RulesConvert Event Types to Action Rules Go to Events Action Rules and click AddTriggers Add Recipients ActionsRecipient Types Set Up Email Recipients Create SchedulesGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesRecording List RecordingsContinuous Recording Go to Recordings ListLanguages Security System OptionsUsers IP Address FilterIeee CertificatesGo to System Options Security Ieee Go to Setup System Options Security Certificates Basic TCP/IP SettingsDate & Time NetworkIPv6 Address Configuration IPv4 Address ConfigurationAssign IP Address Using ARP/Ping ARP/PingAxis Internet Dynamic DNS Service Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service requires IPv4 DNS ConfigurationHost Name Configuration NTP ConfigurationLink-Local IPv4 Address NAT traversal port mapping for IPv4FTP QoS Quality of ServiceUPnPTM StorageRTP/H.264 BonjourMaintenance To add a network shareGo to System Options Storage Click Network Share Support Overview SupportSystem Overview Logs & ReportsReset to Factory Default Settings Plain ConfigFile Upload Upgrade the Firmware TroubleshootingEmergency Recovery Procedure Check the FirmwareProblems setting the IP address Symptoms, Possible Causes and Remedial ActionsProduct cannot be accessed from a browser Product is accessible locally but not externallyStatus and Network indicator LEDs are flashing red rapidly Problems with streaming H.264Video and image problems, general Video Camera SettingsStorage disruption Storage and disk management problemsRe-mount the storage device Reformat the SD card and then click MountTechnical Specifications Installation Function/group Specifications System ApplicationMaintenance General Casing PowerPerformance Considerations M3.6

Related manuals

Manual 82 pages 28.95 Kb