Français, Considérations système | Axis Communications AXIS A1001

specification of the product. These can be provided by Axis or a third party.

•Use only spare parts provided by or recommended by Axis.

•Do not attempt to repair the product by yourself. Contact Axis support or your Axis reseller for service matters.

•The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network switch shall be shielded (STP) and intended for their specific use. Make sure that the network switch is properly grounded. For information about regulatory requirements, see Regulatory Information, on page 2.

•Use a Safety Extra Low Voltage (SELV) compliant limited power source (LPS) with either a rated output power limited to ≤100 W or a rated output current limited to ≤5 A.

•Each wire shall have an area that corresponds to an conductor gauge range of AWG 28–16 (CSA) or AWG 22– 14 (cUL/UL). Select cables in compliance with your local regulations.

•To allow for future maintenance, to avoid excessive strain on wires and connectors, and to avoid damage to conductor insulation, leave a service loop and make sure all cables and wires are properly supported and secured. Use the supplied cable ties.

•Make sure all the wires are connected correctly. Incorrect wiring could cause damage to the product.

•To protect the circuits against electrostatic discharge (ESD), use ESD protection when handling the product while the components and contacts are exposed.

•If using Power over Ethernet, wait with connecting the network cable to the network until the all the other wires have been connected.

•If installing the door controller on a wall, make sure the cut-out for the cables is facing downward.

•The recommended maximum reader data cable length is 30 m (98.4 ft).

•Before installing the product, connect the product to the network and configure the hardware in the product’s hardware configuration pages. Use the generated hardware pin chart. Make sure the product is disconnected from power (PoE/DC) while connecting devices to the product.

•For information about how to connect other wires, such as power wires to locks, readers and other devices, see the manufacturers’ instructions.

Transportation

•When transporting the Axis product, use the original packaging or equivalent to prevent damage to the product.

Battery

The Axis product uses a 3.0 V BR/CR2032 lithium battery as the power supply for its internal real-time clock (RTC). Under normal conditions this battery will last for a minimum of five years.

Low battery power affects the operation of the RTC, causing it to reset at every power-up. When the battery needs replacing, a log message will appear in the product’s server report. For more information about the server report, see the product’s setup pages or contact Axis support.

The battery should not be replaced unless required, but if the battery does need replacing, contact Axis support at ww.axis.com/techsup for assistance.

•Risk of explosion if the battery is incorrectly replaced.

•Replace only with an identical battery or a battery which is recommended by Axis.

•Dispose of used batteries according to local regulations or the battery manufacturer's instructions.

Français

Considérations système

Le produit Axis doit être installé dans une zone sécurisée. Le produit Axis, qu'il s'agisse d'un contrôleur de porte indépendant ou d'un système de contrôleurs de portes, ne doit pas limiter ou avoir un impact négatif sur l'utilisation à laquelle les périphériques qui lui sont raccordés sont destinés.

Le produit Axis doit être installé sur un mur (de préférence) ou un plafond avec ou sans boîte de jonction. Il peut également être installé sur un rail DIN.

Informations sur la sécurité

Lisez attentivement ce guide d'installation avant d'installer l'appareil. Conservez le guide d'installation pour toute référence ultérieure.

Niveaux de risques

Lisez attentivement ce guide d'installation avant d'installer l'appareil Axis. Conservez le guide d'installation pour toute référence ultérieure.

Indique une situation dangereuse qui, si elle n'est pas évitée, entraîne le décès ou des blessures graves.

Indique une situation dangereuse qui, si elle n'est pas évitée, pourrait entraîner le décès ou des blessures graves.

Indique une situation dangereuse qui, si elle n'est pas évitée, pourrait entraîner des blessures légères ou modérées.

Indique une situation qui, si elle n'est pas évitée, pourrait endommager l'appareil.

Autres niveaux de message

Indique les informations importantes, nécessaires pour assurer le bon fonctionnement de l'appareil.

Indique les informations utiles qui permettront d'obtenir le fonctionnement optimal de l'appareil.

Consignes de sécurité

Le produit Axis doit être installé par un professionnel habilité.

•N'installez jamais le produit Axis lorsque le produit est sous tension. Mettez sous tension une fois l'installation terminée.

•Coupez l'alimentation avant de brancher tous les câbles au produit Axis. Ne procédez jamais aux branchements si le produit est sous tension.

•Le produit Axis doit être utilisé conformément aux lois et règlementations locales en vigueur.

•Pour pouvoir utiliser le produit Axis à l'extérieur, ou dans des environnements similaires, il doit être installé dans un boîtier d'extérieur homologué.

•Conserver ce produit Axis dans un environnement sec et ventilé.

•Ne pas exposer ce produit Axis aux vibrations, aux chocs ou

AXIS A1001 specifications

The Axis Communications AXIS A1001 is a state-of-the-art IP-based door controller designed to enhance security and access management in various environments. This device is specifically tailored for organizations looking for a robust solution for controlling access to their facilities while ensuring the safety of personnel and assets.

One of the standout features of the AXIS A1001 is its ability to seamlessly integrate with existing network infrastructures. It supports Power over Ethernet (PoE), which simplifies installation by allowing both power and data to be transmitted through a single cable. This reduces the need for additional electrical wiring, making installation quicker and more cost-effective.

Equipped with a variety of connectivity options, the AXIS A1001 facilitates integration with third-party devices, such as video surveillance systems and intrusion detection systems. This interoperability allows organizations to create a comprehensive security ecosystem that responds to potential threats in real-time.

The AXIS A1001 supports two modes of operation: a standalone mode for smaller applications and a network mode for more extensive and complex access control systems. In standalone mode, the device can be configured and managed locally, while network mode allows for centralized control from a server or cloud-based platform. This flexibility makes the AXIS A1001 suitable for a range of scenarios, from small offices to large enterprises.

Another significant feature is its compatibility with a wide range of credential options, including RFID readers, keypads, and mobile access solutions. This enables organizations to customize their access control systems according to their specific needs. Additionally, the AXIS A1001 is designed to support both entry and exit control, allowing for efficient management of the flow of individuals in and out of premises.

In terms of security, the AXIS A1001 is equipped with advanced encryption standards to protect data transmission and prevent unauthorized access. The device also features tamper detection, which alerts administrators in case of potential tampering with the hardware.

Overall, the Axis Communications AXIS A1001 combines cutting-edge technology with user-friendly features, making it a versatile choice for any organization looking to boost its access control measures and enhance overall security. With its robust performance and integration capabilities, the AXIS A1001 stands out as a reliable solution for today's demanding security challenges.