Kenwood VR-2000 Memory backup function, Remote control unit, For the U.S.A, Setup Codes chart

Memory backup function

Please note that the following items will be deleted from

this unit's memory if the power cord is disconnected

from the AC outlet for approximately three days.

•]'he input selection is cleared and the "Tuner" nput is selected.

•The volume setting is cleared and the volume is set to "-66 dB",

•The receiving band setting is cleared and the "FM" bend _s selected.

VR- 2090/VR-2080/KRF-V8881 D/KRFoV77710 (EniK}

•The frequency setting is cleared and 875 MHz is selected.

•The preset station memory is cleared,

•The surround setting is cleared and reset to the initial condition

Remote control unit

Remote control operation is not possible,	•	Batteries		are	exhausted
	•	The	remote	control unit		is ;oo	far away	from	the
		main	system,		controlling	angle is too large, or
		there is an obstac e in between.
	•	The	audio	cords and system			control	cords	are
		not	connected		properly.
	•	The	source	component		to be operated		does	not
		contain the tapeIs] or disc

•Reprace with new batteries,

•Operate the remote control unit within the controllable range,

•Connect properly referring to "System con- nection",

•Pace the tape(s) or disc in the source compo nent to be played,

The

RC

screen

is

not displayed.

•

Batteries

are

exhausted,

•

Replace

with

new batteries,

The

RC

display

is

abnormal.

•

Batteries

are

removed while something

is dis-

•

Remove

and

replace

batteries after th,e infer-

played

matron

display

has

disappeared.

Setup Codes chart

Although each setup code is designed to work with a number of different models, certain codes may not work with some models. (Also, certain codes may only operate some of the functions available on a given model.}

With some models, be sure to keep the ENTER key pressed for a while.

Inquiries on the setup codes loaded using the Free-Phone Consumer Help Line:

If there is any inquiry related to these setup codes, please contact the following services.

U.S.A. : 1-800-753-9860 Canada : 1-800-644-0073

For the UoS.A.

FCC WARNING

This equipment may generate or use radio frequency energy Changes or modifications to this equtpment may cause harmful interference unless

the mod]ficatons are expressly approved in the instruction manual. The user could lose the authority to operate this equipment f an

unauthorized change or rood fication is made.

NOTE:

This equipment has been tested and found to comply with the Imits for a Cass B digital device, pursuant to Part 15 of the FCC Rules. Ihese

limits are designed to provide reasonable protection against harmful interference m a residential installation. This equipment may cause

harmful interference to radio communications, if it is not installed and used in accordance with the instructions However. there is no

guarantee that interference will not occur in a particu ar installation. If this equipment does cause harmful eterference to radio or telev sion

reception, which can be determined by turning the equipment off and on, the user s encouraged to try to correct the interference by one

or more of the following measures:

--Reorient or relocate the recewrng antenna.

--Increase the separation between the equipment and receiver

-- Connect the equipment into an outlet on a circuit different from that to which the receiver _s connected.

--Consult the dealer or an experienced radio / TV technic an for help.

For the U.S.A,

Note to CATVsystem installer:

This reminder

is

provided

to oall the

CAW

systeminstallnr's

attenbon

to

Article 820-40 of

the NEC

that

provides

guideIines

far

proper

grounding

and,

in

particular,

specifies

that

the cabe ground

shall be connected

to the grouoding

system

of

the building,

as cose

to the

point

of cable

entry

as

practical

j

containingDonotuse oil,contactsince cleaningtheymayagentsdeform becausetheplasticthey componentscouldcase. a malfunction Be specifically careful against using contact cleaning agents