Kenwood VR-2000 Recording a music source, Copying tape TAPE1 --TAPE2 Digital--* digital recording

VR-2OSO/VR2OSO/KRF- -VS881DiKRF+V7771[3[En/K)

When recording sound with a recorder component of KENWOOD, synchro recording is possible by setting the INPUT SELECTOR

to select "Tape1" or "MD" according to the connected component.

Recording a music source

O Select the recording source.

The icons differ according to the setup of +Setup IR" etc.

19 Put the MD recorder or cassette deck to record-pause mode. Select the "Remote Mode" icon from the fixed segments.

_+ Select the "MD/Tapel" icon,

Select the MD or cassette deck control icon and put it to record-pausemode+

O Play the source and record it.

a When the "Remote

Mode"

con is selected,

the

icons of the

components

assigned

to the

inputS,

such

as the "CD1

", "Video 1",

"Video2",

"Video3"

and

"MD/Tapel"

icons

bnk

for a

few

seconds+

By select;nO

a

bI+nkng

icon,

the

selected

component

can

be

controled

without

switching

the

input

selector

(The

"Remote

Mode" con

can be used

to put

the

recording

component

to pause

mode w thout

switching

the

input

selectory

When an icon that is not blinking is selected, the input selector is switched automat sally

•For the recerding procedure of the MD recorder or cassette oeck, refer to its instruction menus

Copying tape (TAPE1 --_TAPE2)

Caution for recording

Digital--* digital recording

The digital signal input through DIGITAL IN is output digitally at the OPTICAL jack+

Make sure the following points to record a digital signal input into the receiver. (The DTS and Dolby Digital (AC-3} signals can- not be recorded,)

Igl Connect the digital output from the source component to the digital input of the receiver

O Connect the digital output (OPTICAL jack) of the receiver to the digital input (OPTICAL jack} of the MD recorder.

O Record the signal on the recorder component (MD recorderl

							l
O	Select	the	"MD/Tapel"		input.
O	Startplayback		of the cassette deck connected to the			MD/TAPE1	]
	input	jacks,	then	start	recording of that connected	to the CD2/
	TAPE2	MONITOR		input	jacks+

Digital-* analog recording

By reproducing the digital signal input to the receiver in stereo

(surround mode), the signal can be recorded in analog with the

following procedure,

O

Set

up the

recorder

component

+eady

for

recording

t_ Select the receiver's input to the source component,

_)

Play the

desired

software.

O

Set

the

"Input

Digital"

icon

from

"Auto"

to

"Manual",

O

In the "Lstn

Mode'* menu

screen,

select

the

"Stereo" icon

O

PFay the

software

from

the

beginning

and

record

it.

•

Do

not switch

to

"CD2/Tape2

(Monitor)"

during

recording,

This

may

cause

the

interruption

of

the

recording,

Note on CD2/ Tape2 (Monitor)

The following

operations

are

made available

by setting

the

"CD2/Tape2

(Monitor)"

icon

on the

"Setup

Input"

menu

screen to

"Tape2

(Monitor)",

However,

remember

that

these

functions

are available

only

when

the

analog

input/output

are

used,

If the

"CD2/Tape2"

icon

in the

fixed

segments

is selected

during

playback

of a digital

input,

the

input

is switched

to

the analog

input

and noise may be generated.

ICON

DISPLAY

@

002 ! TAPE2

MONITOR

"Tape2 (Monitor)" setup menu screen

For the setup of the remote control unit, p[ease read "Set "CD2/Tape2"",

Using "CD2/Tape2"

The CD2/TAPE2

MONITOR

input jacks of the main unit accept e cassette deck or graphic equalizer.

When

a graphic

eelJalizer

is connected,

set "CD2]Tape2"

to

"Tape2"

and

select the

"CD2/Tape2"

icon

in

the

fixed

segments

to

on,

When

a 3+head

cassette

deck

is connected

to the

CD2iTAPE2

MONITOR

_nput jacks,

the

recorded

audio

can

be

monitored

during

recording,

and

turning

"CD2/Tape2"

on

and

off

allows

you to

compare

the

source audio

and

recorded

audio

Refe to the

instructio_

manuals

of

the

connected

components

for the_ operating procedures,

The

"CD2/Tape2

(Monitor)"

funct+on

is

not

ave

Jab e

during

p ayback

of

a digital

input

Se ecting

"CD2/Tspe2

(Monitor)"

durng

dig tal

input

playback

switches the

input

to

the

analog

input