Philips 9P6034C1, 9P5034C1, 9P6031C1, 9P5534C1, 9P5031C1, 9P5531C1 manual Glossary to Television Terms

Page 48

GLOSSARY TO TELEVISION TERMS

Audio/Video Inputs * Located on the rear of the TV these connec- tors (RCA phono type plug) are used for the input of audio and video signals. Designed for use with VCRs (or other accessories) in order to receive higher picture resolution and offer sound connec- tion options.

Coaxial Cable * A single solid antenna wire normally matched with a metal plug (F-type) end connector that screws (or pushes) directly onto a 75 Ohm input found on the Television or VCR.

Display * An on screen message or graphics that help the user operate and adjust TV feature controls. See On Screen Displays (OSD).

Identify* Method by which a remote control searches and finds an operating code for another product (such as a VCR or Cable Converter). Once the code has been "identified" then the TV remote can operate and send commands to the other product.

LED * Light Emitting Diode or indicator.

Menu * An on-screen listing of feature controls shown on the TV screen that are made available for user adjustments.

Multichannel Television Sound (MTS) * The broadcast standard that allows for stereo sound to be transmitted with the TV picture.

On Screen Displays (OSD) * Refers to the wording or messages generated by the TV to help the user with specific feature controls (color adjustment, programming, etc.).

Picture -In-Picture (PIP) * Term used when two pictures are shown on the TV screen at the same time. The smaller PIP picture is supplied by a VCR (or other tuner/video playback source). The PIP picture can also be moved and swapped with the TV's main screen picture.

Pre-Amplifier * The control center of a hi-fi system. Not only amplifies source inputs, but also allows for source selection, vol- ume, tone, balance and all other controls that affect the sound.

Programming * The procedure of adding or deleting channel num- bers into the TV’s memory circuits. In this way the TV “remem- bers’’ only the locally available or desired channel numbers and skips over any unwanted channel numbers.

PTV * Projection Television (Rear and/or Front projection design systems are available.)

Remote Sensor Window * A window or opening found on the TV control panel through which infrared remote control command sig- nals are received.

RF * Radio Frequency or modulated signal design used as the car- rier for television broadcasts.

Second Audio Program (SAP) * Another or additional audio channel provided for in the Multichannel Television Sound (MTS) broadcast standard. A monaural soundtrack included within the recorded or video signal (usually containing a second language translation for the displayed programming.)

Status * Allows the user to quickly confirm what channel number is currently being viewed. Status can also be used to clear the TV of on-screen displays or information (rather than waiting for the displays to “time out” or automatically disappear from the screen).

S-Video Input * Allows direct connection of high-resolution video sources, such as a Super VHS videocassette recorder, Laser Disc player, etc. Provides improved picture resolution, sharpness, and clarity.

Twin Lead Wire * The more commonly used name for the two strand 300 Ohm antenna wire used with many indoor and outdoor antenna systems. In many cases this type of antenna wire requires an additional adapter (or balun) in order to connect to the 75 Ohm Input terminals designed into the more recent Televisions and VCRs.

Variable Audio Output * An adjustable audio output which allows for volume variations at the source.

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Projection Television Warranty Owner Confirmation Safety Instructions Read before operating equipment Table of Contents Features End-of-Life disposalPicture Menu Control Adjustments COLOR, Brightness SHARPNESS, TINT, PicturePicture Menu Controls Flesh CorrectionRED/BLUE Convergence Select Convergence con- trolRemember. Convergence Picture Source Select Picture SourcePress the Menu buttons Feature Menu Controls Closed CaptionSelect Closed Captioning control Cable Tuning Channel Memory AUTO-PROGRAMMING Select Channel MemoryPress the Menu button to turn Press the Status or Menu MADD/DELETE Channels Select Channel MemoryPress the Menu button to Press the Status or MenuSET Clock Select SET Clock controlPress the remotes number buttons to set the time clock Half Hour ReminderSET Alarm Timer Sleep TimerParental Control Setup Code Number Enter a new four digit number code using the remoteFirst lets set your Parental Code Select the Parental CON- TrolParental Control Channel Blocking Select the Channel Blocking controlPress Channel Content Advisory Select the Content AdviParental Control Enter the correct ParentalContent Advisory Movie Ratings Select the Movie Ratings Menu optionSelect the desired Movie Blocking levelContent Advisory Parental Guidelines Select the Parental Guidelines Menu optionContent Advisory Blocking Options Review SettingsSelect the Blocking Options Menu controlChannel Display Select Channel Display controlLanguage Select the Language DIS- Play controlSound Menu Control Adjustments BASS, TREBLE, BalanceSelect BASS, or TREBLE, or Press the + or buttons toSound Menu Control StereoSelect Stereo sound control Second Audio ProgramDisplay Volume Select Display Volume controlSound Menu Controls Incredible StereoTV Speakers Connect the Right and Left Variable Audio OUT jacksSurround Sound Place the speakers so the viewVariable Audio Output Using the AUDIO/VIDEO Input Jacks AUX 1 Video InputsConnect the Video OUT jack Connect the Audio OUTAUX1 S-VIDEO Inputs Connect the S-VIDEO S- VHS OUT jack from the VCR toComponent Video Inputs Connect the Component Y PBSelect the AUX 1 Y PB PR Picture Source control on the TV Using the AUDIO/VIDEO Output Jacks AUDIO/VIDEO OutputsRemote Control Operation Smart PictureHighlighted in red Press the Menu M or butChannel SURF/SMART Surf Setting the TV Remote to Work Accessory Devices Setting the TV Remote to Work Accessory Devices Contin Direct Access MethodSetting the Remote to Work Other Devices Search Search MethodDevice. Point the remote toward Surf and the desired SystemRemote Control Direct Entry Codes for Accessory Devices VCR Brand Remote Code noDVD Brand Remote Code no Using the Remotes VCR Buttons Rewind ButtonSupplied by a VCR or other Connect the Video OUTMove to the next page after Set the TVs PIP Source Select control to AUX1 Video Press the Menu and Menu M buttons toSelect the channel on the VCR to view in the PIP window Press the PIP ON/OFF button on the remoteUsing PIP with the Remote Control Press the PIP ON/OFF button to show the PIP picturePress the PIP Size button to change the size of the PIP win Selecting the Picture Source for PIP PIP SourceSelect PIP Source control Adjusting Picture -IN -PICTURE Color and Tint PIP Color / PIP TintSelect PIP Color or PIP Press the + and buttons toFirst use an optional signal More PIP ConnectionsTV Help Menu Select Help on the TVs Main Menu Press the remotes MenuTV Displays Wrong Channel or No Channels Above Tips if Something Isnt WorkingGlossary to Television Terms Index Philips Consumer Electronics Company Texas Limited Warranty
Top Page Image Contents