Kenwood VR-5900 setup guide Connecting Your Laser Disc Player with AC-3 RF Output, Rf Out

Page 32

Connections

Chapter One : Connecting Your Devices

Connecting Your Laser Disc Player (with AC-3 RF Output)

AC-3

RF OUT

26

DIGITAL OUT OPTICAL or COAXIAL

IR RECEIVER

IR REPEATER OUT/ IR RECEIVER

IR OUT

RELAY

TV ON/OFF SL16 TEXT

SYSTEM

RF RE

IN

DVD CONTROL IN

LCD

CONTROL

SENSOR

CONTROL

ANT

R

L

R SURROUND BACK L

R SURROUND L

R FRONT L

DC12V

IR OUT LCD

DC12V 20mA

REMOTE DC12V 20mA

DC5V 10mA

VIDEO

SUB WOOFER CENTER

20mA

REMOTE

A

ZONE B PRE OUT

PRE OUT

B

DIGITAL OUT

COMPONENT VIDEO

S VIDEO

VIDEO

R AUDIO L

R AUDIO

L

Y
REC	VIDEO1	PHONO
OUT	VIDEO1	PHONO	FM 75Ω
			AM

Remove protective cap before inserting

DIGITAL OUTPUT	RF INPUT	DIGITAL INPUT		DC IN
COAX.	AC-3 RF	COAX.	OPT.

RF DEMODULATOR

DIGITAL OUT

S- VIDEO OUT

VIDEO OUT

AUDIO OUT

			PB/CB			CD1	GND
				PLAY		CD1
DVD				PLAY			ANTENNA
				IN			ANTENNA
			PR/CR			REC
				REC		REC
CD1		VIDEO		REC		OUT
		VIDEO		OUT
		3 IN			VIDEO2	MD/
		DVD	Y		VIDEO2	TAPE1
		DVD	Y	PLAY		TAPE1
MD/		IN		PLAY
TAPE1				IN		PLAY
			PB/CB			IN
			PB/CB			REC
CD-R				PLAY	VIDEO3	OUT
CD-R				IN	VIDEO3	CD2/
				IN		CD2/
			PR/CR			TAPE2
VIDEO			PR/CR			MONITOR
VIDEO				PLAY	VIDEO4
2				IN	VIDEO4	PLAY
2				IN		PLAY
						IN
		MONITOR	Y	PLAY	DVD FRONT	REC
VIDEO		OUT		PLAY		OUT
EXT.CONTROL 3				IN	DVD/
RS-232C					DVD/	CD-R
RS-232C			PB/CB		6CH
			PB/CB		6CH
VIDEO					INPUT
4				MONITOR	SURROUND	PLAY
				MONITOR		PLAY
			PR/CR	OUT		IN
OPTICAL	COAXIAL			OUT		IN
OPTICAL	COAXIAL
DIGITAL IN
					CENTER	SUBWOOFER

Image 32

Contents VR-5900 Before Applying Power A. and Canada AC 120 V onlyPage Unpacking Table of Contents Chapter Four Specifications Before Connection Video signalsBefore You Begin Following diagram shows the entire back of the VR-5900 Sensor jackNoting Your Devices Connecting Your Speakers Front CenterUsing Banana Plugs except for U.K Using Bare WiresTo Connect Front Speakers Only To Connect Front and Surround Sound SpeakersSurround Back Powerd Subwoofer Surround BackWhat if I Have a Powered Subwoofer? To Connect Surround Back SpeakersPowerd Subwoofer Front Center What if I Have an Amplifier?What if I Have an Amplifier? Connecting Your TV Video Composite VideoOn the Receiver? To Connect a TVWhat if I Want to Watch TV without Turning Video OUT Audio OUT Connecting Your Cable TV or Satellite TunerComponent Video OUT To Connect a Satellite Tuner Video OUT Video in Audio OUT Connecting Your VCRsVideo Video OUT To Connect a Primary VCR To Connect a Secondary VCROutput B CD2 Connecting Your Primary CD PlayerOutput a CD1 What if I Have a Video CD-Compatible CD Player? To Connect a Kenwood 200-Disc CD ChangerTo Connect Any Other Primary CD Player or Changer To Connect a Secondary CD PlayerConnecting Your DVD Player Video OUT Subwoofer OUT Center OUT Surround OUT Front OUTTo Connect a DVD Player DTS disclaimer clauseConnecting Your CD-R Recorder Record in Analog Play OUT AnalogTo Connect a CD-R Recorder Connecting Your MD Recorder or Primary Tape Deck Digital Record in Optical or CoaxialTo Connect a Secondary Tape Deck To Connect an MD RecorderTo Connect a Primary Tape Deck Connecting Your Secondary CD Player or Tape Deck To Connect a Secondary CD Player RF Demodulator Digital OUT Video OUT Audio OUT Connecting Your Laser Disc Player with AC-3 RF OutputRF OUT To Connect an AC-3 RF Output Laser Disc Player Connecting Your Laser Disc Player without AC-3 RF Output Before insertingTo Connect a PCM Digital Output Laser Disc Player GND Audio OUT Connecting Your Turntable/Record PlayerTo Connect a Turntable/Record Player Connecting a Camcorder or Additional VCR To Connect a Camcorder or Additional VCRCan I Connect an Additional VCR Permanently? Audio OUT Video OUTSystem Control connection allows you to Connecting the Antennas AM Loop Antenna FM Indoor Antenna RF Remote AntennaFM Outdoor Antenna What if I Have Cable Radio?Installing the Batteries To install the batteriesResetting PowerTouch Calibrating the Touch ScreenSelecting the Model Type To set the model typeNavigating PowerTouch Interface Setup EditHome 1HOME2 To change the time until the screen goes outSP Selection Setting Up SpeakersSpeaker placement RemoteSetup SP DistanceSP Level Bass Peak LevelIdentifying Devices For PowerTouch Control How Do I Replace a Setup Code with a New One?How Do I Delete Setup Codes? How Do I Identify Devices?Storing RDS Station Name PS Read Storing Radio Stations in Memory optionalStoring RDS Stations Automatically Name input of the preset station Storing Stations ManuallyChanging the item size To Customize the PowerTouch ScreenChanging the name Moving an item Cutting an itemCopying an item Pasting an itemLocking customization results with password Resetting to defaultSwitching the customized screen to another Jump To undo the last operation performedSpeaker setup Setting Up on the ReceiverPreparation for setup Storing Stations Manually Storing Radio Stations in Memory optionalStoring RDS Stations Automatically RF Remote Control Function Changing the RF Transmission FrequencyZone a Zone BBoth Scenarios Connecting a Second TV/ Monitor Making ConnectionsSetting Up the PowerTouch Connecting the External Infrared Receivers and IR Repeaters IR ReceiverAdaptor IR OUTConnecting the External Infrared Receivers and IR Repeaters To Connect a Kenwood IR-9991 IR ReceiverTo Connect any other IR Receiver To Connect IR RepeatersConnecting and Setting Up On/Off Sensors or Relay Controls Relay ControlControlled DeviceTo Connect Relay Controls To Connect TV ON/OFF SensorsFCC Compliance Notice ICIndustry Canada NoticeVideo Section Index VCR For your records