Kenwood VR-5900 setup guide Noting Your Devices

Page 9

Chapter One : Connecting Your Devices

Noting Your Devices

Jack Set

Device

Manufacturer

Model #

Setup Code

 

 

 

 

 

PHONO

CD1

MD/TAPE1

CD2/TAPE2 MONITOR

CD-R

MONITOR OUT

3

(TV on PowerTouch)

 

 

 

VIDEO1

 

 

 

VIDEO2

VIDEO3

VIDEO4

DVD

Connections

Use this table and the diagram on the preceding page to plan your connections before you make them, or use it to record your connections as you make them.

You will need this information later, when you set up your PowerTouch (see “Identifying Devices For PowerTouch Con- trol” on page 40). Recording this information now will save you additional trips behind your home entertainment cabi- net. You will fill in the Setup Code column when you are setting up PowerTouch.

When playing Dolby Digital*1 or DTS-encoded software in multichannel configuration, the connected audio signal should be the digital signal.

*1 When playing a LaserDisc recorded in the Dolby Digital format, connect the AC-3 RF output to the receiver (See page 26).

Image 9
Contents VR-5900 A. and Canada AC 120 V only Before Applying PowerPage Unpacking Table of Contents Chapter Four Specifications Video signals Before You BeginBefore Connection Sensor jack Following diagram shows the entire back of the VR-5900Noting Your Devices Front Center Connecting Your SpeakersUsing Bare Wires Using Banana Plugs except for U.KTo Connect Front Speakers Only To Connect Front and Surround Sound SpeakersSurround Back Surround Back Powerd SubwooferTo Connect Surround Back Speakers What if I Have a Powered Subwoofer?What if I Have an Amplifier? Powerd Subwoofer Front CenterWhat if I Have an Amplifier? Video Composite Video Connecting Your TVTo Connect a TV What if I Want to Watch TV without TurningOn the Receiver? Connecting Your Cable TV or Satellite Tuner Component Video OUTVideo OUT Audio OUT To Connect a Satellite Tuner Connecting Your VCRs Video Video OUTVideo OUT Video in Audio OUT To Connect a Secondary VCR To Connect a Primary VCRConnecting Your Primary CD Player Output a CD1Output B CD2 To Connect a Kenwood 200-Disc CD Changer What if I Have a Video CD-Compatible CD Player?To Connect Any Other Primary CD Player or Changer To Connect a Secondary CD PlayerVideo OUT Subwoofer OUT Center OUT Surround OUT Front OUT Connecting Your DVD PlayerDTS disclaimer clause To Connect a DVD PlayerRecord in Analog Play OUT Analog Connecting Your CD-R RecorderTo Connect a CD-R Recorder Digital Record in Optical or Coaxial Connecting Your MD Recorder or Primary Tape DeckTo Connect an MD Recorder To Connect a Primary Tape DeckTo Connect a Secondary Tape Deck Connecting Your Secondary CD Player or Tape Deck To Connect a Secondary CD Player Connecting Your Laser Disc Player with AC-3 RF Output RF OUTRF Demodulator Digital OUT Video OUT Audio OUT To Connect an AC-3 RF Output Laser Disc Player Before inserting Connecting Your Laser Disc Player without AC-3 RF OutputTo Connect a PCM Digital Output Laser Disc Player Connecting Your Turntable/Record Player To Connect a Turntable/Record PlayerGND Audio OUT To Connect a Camcorder or Additional VCR Connecting a Camcorder or Additional VCRCan I Connect an Additional VCR Permanently? Audio OUT Video OUTSystem Control connection allows you to AM Loop Antenna FM Indoor Antenna RF Remote Antenna Connecting the AntennasFM Outdoor Antenna What if I Have Cable Radio?To install the batteries Installing the BatteriesCalibrating the Touch Screen Resetting PowerTouchSelecting the Model Type To set the model typeSetup Edit Navigating PowerTouch InterfaceHome 1HOME2 To change the time until the screen goes outSetting Up Speakers Speaker placementSP Selection SP Distance RemoteSetupBass Peak Level SP LevelHow Do I Replace a Setup Code with a New One? Identifying Devices For PowerTouch ControlHow Do I Delete Setup Codes? How Do I Identify Devices?Storing Radio Stations in Memory optional Storing RDS Stations AutomaticallyStoring RDS Station Name PS Read Storing Stations Manually Name input of the preset stationTo Customize the PowerTouch Screen Changing the nameChanging the item size Cutting an item Moving an itemCopying an item Pasting an itemResetting to default Locking customization results with passwordSwitching the customized screen to another Jump To undo the last operation performedSetting Up on the Receiver Preparation for setupSpeaker setup Storing Radio Stations in Memory optional Storing RDS Stations AutomaticallyStoring Stations Manually Changing the RF Transmission Frequency RF Remote Control FunctionZone B Zone aMaking Connections Both Scenarios Connecting a Second TV/ MonitorSetting Up the PowerTouch IR Receiver Connecting the External Infrared Receivers and IR RepeatersAdaptor IR OUTTo Connect a Kenwood IR-9991 IR Receiver Connecting the External Infrared Receivers and IR RepeatersTo Connect any other IR Receiver To Connect IR RepeatersRelay Control Connecting and Setting Up On/Off Sensors or Relay ControlsControlled DeviceTo Connect TV ON/OFF Sensors To Connect Relay ControlsICIndustry Canada Notice FCC Compliance NoticeVideo Section Index VCR For your records