Kenwood VR-5900 setup guide To Connect an AC-3 RF Output Laser Disc Player

Page 33

Chapter One : Connecting Your Devices

Connecting Your Laser Disc Player (with AC-3 RF Output), continued

Connections

Do not plug in the receiver to AC power until you have connected all your devices.

You must purchase an RF Demodulator (DEM-9991D) if you plan to operate a player with a Dolby Digital (AC-3) RF Output with this receiver.

These instructions describe how to connect a laser disc player with an AC-3 RF Output. If your laser disc player does not have an AC-3 RF output, see “Connecting Your Laser Disc Player (without AC-3 RF Output)” on page 28. Please refer to your laser disc player’s instructions for more detail about its connection jacks and capabilities.

The instructions in this section show one of several pos- sible variations on connecting your laser disc player. For further assistance on optional configurations, contact the store where you purchased your receiver.

To Connect an AC-3 RF Output Laser Disc Player:

1.Review the information under “Before You Begin” on page 1. It contains important notes about the types of video connections you can make.

2.Connect the audio cables from the laser disc player’s Audio OUT jacks to the receiver’s AUDIO jacks (VIDEO 4 PLAY IN) as shown to the left.

Do not connect the digital cable (optical or coaxial) yet; it must be connected via the demodulator as de- scribed in the following steps.

3.Connect the AC-3 RF coaxial cable from the laser disc player’s AC-3 RF OUT jack to the demodulator’s RF IN- PUT AC-3 RF jack as shown to the left.

4.Connect the digital cable (either optical or coaxial) from the laser disc player’s digital jack to the appropriate DIGITAL INPUT jack on the demodulator as shown to the left. Set the switch on the front of the DEM-9991D to the type of connection you made.

5.Connect the coaxial digital cable from the demodulator’s DIGITAL OUTPUT COAX. jack to the receiver’s VIDEO4 COAXIAL jack.

6.Connect the demodulator’s supplied 12V AC adapter to the DC IN jack on the demodulator. Do not plug the adapter into the wall until you have finished making all connections to the receiver.

7.Go to “Noting Your Devices” on page 3 and note which jacks you used to connect your laser disc player. In ad- dition, note the brand name and model number of the laser disc player.

When playing Dolby Digital*1 or DTS-encoded software in 27 multichannel configuration, the connected audio signal should be the digital signal.

*1 When playing a LaserDisc recorded in the Dolby Digital format, connect the AC-3 RF output to the receiver.

Image 33
Contents VR-5900 A. and Canada AC 120 V only Before Applying PowerPage Unpacking Table of Contents Chapter Four Specifications Video signals Before You BeginBefore Connection Sensor jack Following diagram shows the entire back of the VR-5900Noting Your Devices Front Center Connecting Your SpeakersUsing Bare Wires Using Banana Plugs except for U.KTo Connect Front Speakers Only To Connect Front and Surround Sound SpeakersSurround Back Surround Back Powerd SubwooferTo Connect Surround Back Speakers What if I Have a Powered Subwoofer?What if I Have an Amplifier? Powerd Subwoofer Front CenterWhat if I Have an Amplifier? Video Composite Video Connecting Your TVTo Connect a TV What if I Want to Watch TV without TurningOn the Receiver? Connecting Your Cable TV or Satellite Tuner Component Video OUTVideo OUT Audio OUT To Connect a Satellite Tuner Connecting Your VCRs Video Video OUTVideo OUT Video in Audio OUT To Connect a Secondary VCR To Connect a Primary VCRConnecting Your Primary CD Player Output a CD1Output B CD2 To Connect a Kenwood 200-Disc CD Changer What if I Have a Video CD-Compatible CD Player?To Connect Any Other Primary CD Player or Changer To Connect a Secondary CD PlayerVideo OUT Subwoofer OUT Center OUT Surround OUT Front OUT Connecting Your DVD PlayerDTS disclaimer clause To Connect a DVD PlayerRecord in Analog Play OUT Analog Connecting Your CD-R RecorderTo Connect a CD-R Recorder Digital Record in Optical or Coaxial Connecting Your MD Recorder or Primary Tape DeckTo Connect an MD Recorder To Connect a Primary Tape DeckTo Connect a Secondary Tape Deck Connecting Your Secondary CD Player or Tape Deck To Connect a Secondary CD Player Connecting Your Laser Disc Player with AC-3 RF Output RF OUTRF Demodulator Digital OUT Video OUT Audio OUT To Connect an AC-3 RF Output Laser Disc Player Before inserting Connecting Your Laser Disc Player without AC-3 RF OutputTo Connect a PCM Digital Output Laser Disc Player Connecting Your Turntable/Record Player To Connect a Turntable/Record PlayerGND Audio OUT To Connect a Camcorder or Additional VCR Connecting a Camcorder or Additional VCRCan I Connect an Additional VCR Permanently? Audio OUT Video OUTSystem Control connection allows you to AM Loop Antenna FM Indoor Antenna RF Remote Antenna Connecting the AntennasFM Outdoor Antenna What if I Have Cable Radio?To install the batteries Installing the BatteriesCalibrating the Touch Screen Resetting PowerTouchSelecting the Model Type To set the model typeSetup Edit Navigating PowerTouch InterfaceHome 1HOME2 To change the time until the screen goes outSetting Up Speakers Speaker placementSP Selection SP Distance RemoteSetupBass Peak Level SP LevelHow Do I Replace a Setup Code with a New One? Identifying Devices For PowerTouch ControlHow Do I Delete Setup Codes? How Do I Identify Devices?Storing Radio Stations in Memory optional Storing RDS Stations AutomaticallyStoring RDS Station Name PS Read Storing Stations Manually Name input of the preset stationTo Customize the PowerTouch Screen Changing the nameChanging the item size Cutting an item Moving an itemCopying an item Pasting an itemResetting to default Locking customization results with passwordSwitching the customized screen to another Jump To undo the last operation performedSetting Up on the Receiver Preparation for setupSpeaker setup Storing Radio Stations in Memory optional Storing RDS Stations AutomaticallyStoring Stations Manually Changing the RF Transmission Frequency RF Remote Control FunctionZone B Zone aMaking Connections Both Scenarios Connecting a Second TV/ MonitorSetting Up the PowerTouch IR Receiver Connecting the External Infrared Receivers and IR RepeatersAdaptor IR OUTTo Connect a Kenwood IR-9991 IR Receiver Connecting the External Infrared Receivers and IR RepeatersTo Connect any other IR Receiver To Connect IR RepeatersRelay Control Connecting and Setting Up On/Off Sensors or Relay ControlsControlled DeviceTo Connect TV ON/OFF Sensors To Connect Relay ControlsICIndustry Canada Notice FCC Compliance NoticeVideo Section Index VCR For your records