Classe Audio CAP-2100 Troubleshooting, Everything appears to be on, but there is no sound

Page 38

Important!

Important!

38

Troubleshooting

In general, you should refer any service problems to your Classé dealer. Before contacting your dealer, check to see if the problem is listed here. If it is, try the suggested solutions. If none of these solves the problem, contact your Classé dealer.

1.Everything appears to be on, but there is no sound.

•Adjust the volume control to a moderate level (one that should be audible but is not excessive).

•Make sure the source component for which the input has been selected is switched on and is out of its standby mode.

•Make sure the proper input has been selected for the source being used.

•Check that the integrated amplifier is not in mute mode. This is indicated by the operational menu icon in the form of a speaker with a bar through it. Press Mute to disengage.

•Check if the tape monitor is enabled. If it is engaged and the recorder is off, you will not hear the selected source. Disengage by pressing Tape, unless you wish to monitor the recording.

•If the problem occurs only with a particular input, check the interconnect cables between that source and the integrated amplifier.

•If the problem occurs with all inputs, check the speaker wires for secure connections.

Check that the integrated amplifier is off before checking any connections between the integrated amplifier and power amplifier, or between the power amplifier and the speakers.

2.There is no sound and the Standby LED is not lit.

•Ensure the integrated amplifier is plugged into the AC mains and switched on, and that the AC mains are operating normally. The unit will automatically attempt to protect itself from improper AC mains voltages by not powering up.

•If your integrated amplifier was plugged in properly, try the

following: put it in standby, switch off the main power switch in the back, and unplug the unit for at least thirty seconds before trying to power it up again. (Sometimes a brownout of short-term loss of power might require a restart.)

Make sure to power down your integrated amplifier before doing the restart.

•If none of these solutions work, please consult your Classé dealer for assistance. Never attempt to replace an internal fuse. There are no user-serviceable parts inside your unit.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents CAP-2100 Integrated Amplifier Page Important Safety Instructions Do not use this apparatus near waterContents Version info Sensors Word about installation Welcome to the Classé familyUnpacking and Placement Placement Ventilation Custom installationsOperating voltage Warm up/break-in period Special Design Features Extraordinary longevity Off Standby button & LED indicatorFront Panel Mute button Menu buttonLCD touchscreen IR windowVolume Knob Single-ended RCA main outputs Rear PanelSpeaker Outputs Tape Input Optional phono preampTape output Single-ended RCA inputsPin 3 Signal inverting IR Input and OutputDC Trigger Input and Output Classé CAN-Bus Control PortsRS-232 Control Port Ground terminalAC Mains Power Switch AC Mains FuseNavigation Keys Remote ControlBasic Functions Input Selection System ControlsInput selection Tape loop Menu SystemOperational menu Main menu system System setup Rotary Page Input Page Phono gain Triggers Max volume CAP-2400 Teach IR Display setup Brightness Timeout Language Colors Volume Main balance Remote Fkeys CAN-Bus StatusVersion info Sensors Category 5 Network Cables Features Hardware setupClassé Delta Series Products CAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface BoxUsing CAN-Bus Configuration Operate AC status Status Name Global brightness Global standby PlayLinkAmp info Event log There is no sound and the Standby LED is not lit TroubleshootingEverything appears to be on, but there is no sound If your integrated amplifier was plugged in properly, tryThere is a hum coming out of the speakers IR remote control seems not to functionOnly one speaker seems to be playing There is a mechanical hum coming from the unit AC mains fuse is blownMains voltage 100/120VAC Fuse type Mains voltage 230/240VAC Fuse typeCare and Maintenance Cleaning the cabinetSpecifications Dimensions Page Email classe@bwgroup.hk Email cservice@classeaudio.comEmail classe@bwgroup.com
Related manuals
Manual 46 pages 20.49 Kb

CAP-2100 specifications

The Classe Audio CAP-2100 is a remarkable integrated amplifier that stands out in the realm of high-fidelity audio equipment. Designed for audiophiles who seek a blend of exceptional performance and elegant aesthetics, this amplifier is remarkable for its combination of advanced technologies and user-friendly features.

One of the standout features of the CAP-2100 is its Class A/AB amplification, which delivers a powerful and dynamic sound signature while preserving musicality and detail. With its robust output of 100 watts per channel into 8 ohms, the CAP-2100 is capable of driving a wide range of loudspeakers with ease, ensuring that every nuance of the audio is reproduced accurately. This amplifier is engineered to handle difficult loads and deliver a clean sound that remains stable even at higher volumes.

The CAP-2100 incorporates advanced digital signal processing, which optimizes the audio reproduction for various listening environments. This technology ensures that audio is tailored to the specific characteristics of the room, offering a customizable listening experience for users. Additionally, the amplifier features a built-in DAC (digital-to-analog converter) that supports high-resolution audio formats, allowing for playback of your favorite digital files with stunning clarity and depth.

Another impressive aspect of the CAP-2100 is its comprehensive connectivity options. The amplifier provides multiple inputs, including balanced XLR and unbalanced RCA connections, making it versatile enough to accommodate various source components. This connectivity flexibility ensures seamless integration into any existing audio setup.

The design of the Classe Audio CAP-2100 is as intuitive as it is beautiful. The front panel features a sleek, minimalist aesthetic with a large volume knob and easy-to-read indicators. The build quality is excellent, with a solid chassis that minimizes the impact of external interference, further enhancing audio performance.

In summary, the Classe Audio CAP-2100 integrated amplifier is a true testament to high-fidelity audio engineering. Its combination of power, sophistication, and versatility, along with advanced technologies and user-centric design, makes it a fantastic choice for those who demand the best in their audio systems. Whether listening to your favorite vinyl record or streaming high-resolution digital music, the CAP-2100 ensures an unparalleled listening experience that will satisfy even the most discerning audiophiles.
Top Page Image Contents