Classe Audio CAP-2100 owner manual Specifications

Page 43

Specifications

All specifications are accurate at the time of printing. Classé reserves the right to adjust specifications without notice.

n

Power output (both channels driven)

100W/ch continuous rms @ 8Ω

 

Frequency response

 

200W/ch continuous rms @ 4Ω

n

 

10Hz – 22kHz (+0/-0.1dB)

 

Phase

 

10Hz – 155kHz (+0/-3.0dB)

n

 

 

less than -10° @ 22kHz

n

Signal-to-noise ratio

 

 

95dB typical

n

Channel separation

 

better than 95dB @ 20kHz

n

Noise floor (FFT)

 

all peaks less than -90dBV

 

 

 

 

(10Hz – 80kHz)

n

Distortion (THD + noise)

 

 

0.005% @ 8Ω

 

(unweighted, 0.8Vrms/1kHz input, 10Hz – 80kHz)

n

Maximum input voltage

 

 

3.8Vrms (single-ended)

 

Voltage gain range

 

 

7.8Vrms (balanced)

n

 

 

-100dB to +14dB

n

Sensitivity (SSP input)

0.5Vrms for rated output (single-ended)

 

 

 

1.0Vrms for rated output (balanced)

n

Input Impedance

 

 

 

100kΩ

n

Output Impedance (main output)

 

 

100Ω

n

Input complement

1 balanced (XLR), 4 single-ended (RCA)

n

Output complement

 

 

2 single-ended (RCA)

n

Crosstalk (any input to any output)

 

better than -95dB

n

Rated power consumption (as per IEC60065 -

para.2.3.10)

260W

n

Idle power consumption

 

 

 

125W

n

Mains voltage

 

specified on rear panel decal

 

 

 

(cannot be changed by user or dealer)

n

Dimensions (not incl. controls or connectors)

Width: 17.5” (445mm)

 

 

 

 

Height: 4.75” (121mm)

 

Shipping weight

 

 

Depth: 16.5” (419mm)

n

 

 

59lbs (27kg)

n

Net weight

 

 

50lbs (23kg)

For more information, see your Classé dealer, or contact:

Classé Audio

5070 François Cusson

Lachine, Quebec

Canada H8T 1B3

Telephone

+1 (514) 636-6384

FAX

+1 (514) 636-1428

Internet:

http://www.classeaudio.com

email:

cservice@classeaudio.com

Classé and the Classé logo are trademarks of Classé Audio Inc. of Lachine, Canada. All rights reserved. i-Command™ is a trademark of Equity International, Inc. All rights reserved.

AMX® is a registered trademark of AMX Corporation of Richardson, TX. All rights reserved. Crestron™ is a trademark of Crestron Electronics, Inc. of Rockleigh, NJ. All rights reserved.

43

Image 43
Contents CAP-2100 Integrated Amplifier Page Do not use this apparatus near water Important Safety InstructionsContents Version info Sensors Welcome to the Classé family Word about installationPlacement Ventilation Custom installations Unpacking and PlacementOperating voltage Warm up/break-in period Special Design Features Extraordinary longevity Front Panel Standby button & LED indicatorOff IR window Menu buttonLCD touchscreen Mute buttonVolume Knob Speaker Outputs Rear PanelSingle-ended RCA main outputs Single-ended RCA inputs Optional phono preampTape output Tape InputIR Input and Output Pin 3 Signal invertingGround terminal Classé CAN-Bus Control PortsRS-232 Control Port DC Trigger Input and OutputAC Mains Fuse AC Mains Power SwitchBasic Functions Remote ControlNavigation Keys System Controls Input SelectionOperational menu Menu SystemInput selection Tape loop Main menu system System setup Rotary Page Input Page Phono gain Triggers Max volume CAP-2400 Teach IR Display setup Brightness Timeout Language Colors Volume Main balance Remote Fkeys Version info Sensors StatusCAN-Bus CAN-Bus Terminator SSP-300 & 600 CAN-Bus Interface Box Features Hardware setupClassé Delta Series Products Category 5 Network CablesUsing CAN-Bus Configuration Operate AC status Status Name PlayLink Global brightness Global standbyAmp info Event log If your integrated amplifier was plugged in properly, try TroubleshootingEverything appears to be on, but there is no sound There is no sound and the Standby LED is not litOnly one speaker seems to be playing IR remote control seems not to functionThere is a hum coming out of the speakers AC mains fuse is blown There is a mechanical hum coming from the unitMains voltage 230/240VAC Fuse type Mains voltage 100/120VAC Fuse typeCleaning the cabinet Care and MaintenanceSpecifications Dimensions Page Email classe@bwgroup.com Email cservice@classeaudio.comEmail classe@bwgroup.hk
Related manuals
Manual 46 pages 20.49 Kb

CAP-2100 specifications

The Classe Audio CAP-2100 is a remarkable integrated amplifier that stands out in the realm of high-fidelity audio equipment. Designed for audiophiles who seek a blend of exceptional performance and elegant aesthetics, this amplifier is remarkable for its combination of advanced technologies and user-friendly features.

One of the standout features of the CAP-2100 is its Class A/AB amplification, which delivers a powerful and dynamic sound signature while preserving musicality and detail. With its robust output of 100 watts per channel into 8 ohms, the CAP-2100 is capable of driving a wide range of loudspeakers with ease, ensuring that every nuance of the audio is reproduced accurately. This amplifier is engineered to handle difficult loads and deliver a clean sound that remains stable even at higher volumes.

The CAP-2100 incorporates advanced digital signal processing, which optimizes the audio reproduction for various listening environments. This technology ensures that audio is tailored to the specific characteristics of the room, offering a customizable listening experience for users. Additionally, the amplifier features a built-in DAC (digital-to-analog converter) that supports high-resolution audio formats, allowing for playback of your favorite digital files with stunning clarity and depth.

Another impressive aspect of the CAP-2100 is its comprehensive connectivity options. The amplifier provides multiple inputs, including balanced XLR and unbalanced RCA connections, making it versatile enough to accommodate various source components. This connectivity flexibility ensures seamless integration into any existing audio setup.

The design of the Classe Audio CAP-2100 is as intuitive as it is beautiful. The front panel features a sleek, minimalist aesthetic with a large volume knob and easy-to-read indicators. The build quality is excellent, with a solid chassis that minimizes the impact of external interference, further enhancing audio performance.

In summary, the Classe Audio CAP-2100 integrated amplifier is a true testament to high-fidelity audio engineering. Its combination of power, sophistication, and versatility, along with advanced technologies and user-centric design, makes it a fantastic choice for those who demand the best in their audio systems. Whether listening to your favorite vinyl record or streaming high-resolution digital music, the CAP-2100 ensures an unparalleled listening experience that will satisfy even the most discerning audiophiles.