
INSTALLATION
SPEAKER CONNECTION
ANTENNA PLUG |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
| 12P |
|
|
|
|
|
|
|
|
|
|
| |
MEMORY B+ | YELLOW |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
| FUSED |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||||
BLACK(GND) |
|
|
|
| FILTER |
|
|
|
|
|
|
|
| |||
|
|
|
| BOX |
|
|
|
|
|
|
|
| ||||
RED (B+) |
|
|
|
| 0.5A &7A |
|
|
|
|
|
|
| ||||
|
|
|
| FUSES |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||||
BLUE AUTO ANT | 1 A |
|
|
|
|
|
| |||||||||
| + |
|
|
|
| FUSE |
|
|
|
|
|
| ||||
FRONT |
| WHITE |
|
|
|
|
|
| ||||||||
LEFT |
|
|
| WHITE/BLACK |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| ||||||||
SP | + |
| GREEN |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| |||||||
REAR |
|
|
| GREEN/BLACK |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| AUX LINE IN |
|
|
|
|
|
|
|
|
|
|
|
| RED R |
|
|
|
|
|
|
|
|
|
|
|
|
|
| WHITE L |
RCA LINE OUT |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| RED R | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| WHITE L |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| GRAY | + |
|
|
|
| FRONT | |||||||
|
|
|
|
|
|
| ||||||||
| GRAY/BLACK |
|
|
|
|
|
| RIGHT | ||||||
|
|
| ||||||||||||
| VIOLET | + |
|
|
|
| SP | |||||||
|
|
|
|
|
| |||||||||
| VIOLET/BLACK |
|
|
|
|
|
| REAR | ||||||
|
|
If you want to take CHASSIS out of the SLIDE BRACKET HOUSING, remove the PLASTIC OUTLINE away, then insert the two KEY PLATE into left and right side of chassis as the above illustration.
NOTE:
1.In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level.
2.Prohibit to make the conductors of auto antenna and ground
touch with each other.
USA EUROPE
IMPORTANT:
This radio is set to USA frequency by factory, if European frequency is required please flip the frequency step switch on the side of the unit.
After the switchover of the frequency switch, the frequency convert function will not be valid until the RESET button has been pressed. (The RESET button is in the rear facet of the front panel)
9 | 2 |
|