Pyramid Car Audio CDR83MP instruction manual Trouble Shooting

Page 5

TROUBLE SHOOTING

Go through the check list if you are in trouble during operation. If any problem persist after going though the check list, consult your nearest service dealer.

Symptom

Cause

Solution

 

 

 

 

The car ignition is not on.

If the power supply is properly

No power

 

connected to the car accessory

 

switch the ignition key to " ACC "

 

 

 

 

 

 

The fuse is blown

Replace the fuse

 

 

 

Disc cannot

Presence of CD disc inside

Remove the disc in the player

the player

then put a new upward

be loaded or

 

 

Inserting the disc in upside

Insert the compact disc with

ejected

 

down

the label facing upward

 

Compact disc is extremely

Clean the disc or try to play a

 

dirty or defective

new one

 

 

 

 

Temperature inside the

Cool off until the ambient

 

car is too high

temperature returns to normal

 

 

 

 

Condensation

Leave the player off for an

 

 

hour or so, then try again

 

 

 

No sound

Volume is in minimum

Adjust volume to a desired level

 

 

 

Wiring is not properly

Check wiring connection

 

connected

 

 

 

 

 

The operation

The built-in microcomputer

Press the RESET button

keys do not

is not operating properly

front panel is not properly

work

due to noise

fix into its place

 

 

 

Sound skips

The installation angle

Adjust the installation angle

is more than 30 degrees

to less than 30 degrees

 

 

 

 

 

The disc is extremely

Clean the compact disc/try to

 

dirty or defective

play a new one

 

 

 

The radio does

 

 

not work

The antenna cable is not

Insert the antenna cable firmly

the radio

connected

 

station

the signals are too weak

select a station manually

automatic

 

 

selection does

 

 

not work

 

 

 

 

 

2)Press the + button or - button to increase or decrease the sound level of left or right speaker.

FADER CONTROL

1)Press the SEL button to select the fader mode until FAD appears on the display.

2)Press the + button or - button to increase or decrease the sound level of front or rear speaker.

5.LCD ( LIQUID CRYSTAL DISPLAY)

6.MUTE BUTTON

Press it to eliminate the sound immediately.

7.TUNE SEEK UP/DOWN, TRACK UP/DOWN BUTTONS

During RADIO mode, press UP or DN button to seek up or down for the desired station. Press UP or DN button hold for more than 2 seconds to scan up or down for the stronger station.

During CD mode, Press the UP or DN button to allow you to track forward or backward. Press UP or DN button hold to skip forward or backward.

8.POWER BUTTON

Press the button to turn on or off the unit.

9.BAND/LOUD BUTTON

Press it to select your desired radio band and word which band is selected will be displayed on LCD.

Press it hold for more than 2 seconds to enhance the bass sound effect.

10.CLOCK ADJUSTMENT BUTTON

During frequency display, press it to change to clock display function. Press the button for more than 2 seconds, until time flashes, then press UP or DN button to adjust hour or minute.

11.MODE BUTTON

Press it repeatedly to select CDP, AUX and RADIO mode in sequence and circulation.

12.DSP BUTTON

Press it to switch between 4 preset equalizer curves: FLAT, CLASSIC, POP and ROCK, and the sound quality will be changed.

13.PRESET STATION [ 1-6 ] /1PUS, 2SCN, 3RPT, 4SHF.

A]. To memorize the current frequency, press any one of the six preset buttons hold for more than 2 seconds.

B]. To recall the preset memory, press one of the preset button [1-6].

C). In CDP mode, press 1PUS button to pause CDP playing, press it again to resume CDP playing.

7

4

Image 5 Pyramid Car Audio CDR83MP instruction manual Trouble Shooting
Contents Model CDR83MP Remote Control Basics Battery ReplacementBattery Information Dear Customer Disc PlaySpeaker Connection InstallationLocation and Function of Controls SpecificationGeneral Trouble Shooting AS/PS Clock Mode VOL SEL CHAR. Shift VOL UP/DOWNBand Dspsound Mute