POWER AMPLIFIER SECTION
Rated power and load:
700 Watt RMS into 2 Ohms
475 Watt RMS into 4 Ohms
275 Watt RMS into 8 Ohms
Power @ clipping (typically):
(1 kHz, 120 VAC line)
490 Watt RMS into 4 Ohms @ 1% THD
550 Watt RMS into 4 Ohms @ 5% THD
Frequency response:
Total harmonic distortion:
Less than 0.25%, 100 mW to 450 Watt RMS, 20 Hz to 10 kHz, 4 Ohms (typically below 0.1%)
DDT™ dynamic range:
Greater than 20 dB
DDT™ maximum THD:
Below 0.5% THD for 3 dB overload Below 1% THD for 13 dB overload
Hum and noise:
Greater than 90 dB below rated power
Power consumption:
1,200 Watt @ 120 VAC 50/60 Hz
PREAMP SECTION:
The following specs are measured @
1 kHz with the Low, Mid and High EQ @ 0 dB; Contour @ 0; Mid Shift @ 1 kHz; Input Pad and Bright switch out (off); Post Gain @ 10; Nominal levels are with Pre Gain @ 5; Minimum levels are with Pre Gain @ 10.
Passive preamp input (input pad switch “out”):
Impedance:
High Z, 220 k Ohms Nominal Input Level:
+10 dBV, 3 Volt RMS
MAX® 700
ESPECIFICACIONES
Active Preamp Input (Input Pad switch “in”):
Impedance:
High Z, 68 k Ohms
Nominal input level:
Minimum input Level:
Preamp output:
Load impedance:
1 k Ohms or greater Nominal output level:
0 dBV, 1V RMS Maximum output level:
+20 dBV, 10 Volt RMS
Power amp input:
Impedance:
High Z, 22 k Ohms
Designed input level:
0 dBV, 1V RMS
(Switching jack providing preamp output to power amp input connection when not used)
System hum and noise @ nominal input level:
(20 Hz to 20 kHz unweighted) Greater than 75 dB below rated power
Equalization:
Low and high:
±15 dB @ 40 Hz and 7 kHz, shelving Mid:
±15 dB @ mid shift setting Mid shift:
Variable from 200 Hz to 2 kHz Contour:
Special EQ voicing
Push bright:
+8 dB @ 8 kHz
Variable crossover:
Frequency range: 100 Hz to 1 kHz
Slope:
12 dB per octave
Crossover low output:
Load impedance:
1 k Ohms or greater Nominal output level:
0 dBV, 1V RMS Maximum output level:
+20 dBV, 10 Volt RMS
Crossover high output:
Load Impedance:
1 k Ohms or greater Nominal output level:
0 dBV, 1V RMS Maximum output level: +20 dBV, 10V RMS
Effects loop:
Send level:
1 k Ohms or greater Return level:
220 k Ohms
Tuner Send: Level:
Buffered off the Input jack; Dependent on instrument level
Load impedance:
1 k Ohms or greater Low Z balanced line out:
(600 Ohm transformer balanced; Nominal levels with Pre Gain and Line Out Level @ 5; Maximum levels with Pre Gain and Line Out Level @ 10)
Nominal
Nominal
Maximum
Maximum
Weight:
50.9 lbs.
Dimensions: (W x H x D)
23.375" W x 8.250" H x 12.875" D
Salida para preamplificador/amplificador de potencia con enchufes hembra.
17