Phoenix Gold TI2 1000.4 FRONT, Rear and SUB Inputs, SUB Input Switch, Rear X-OVER Config, Phase

Page 5

Amplifier Owner’s Manual

TI2 1600.5

5 CHANNEL POWER AMPLIFIER

FRONT, REAR AND SUB INPUTS

Connect preamp signal cables from headunit to these inputs.

SUB INPUT SWITCH

Determines which input will feed signal to the subwoofer channel. “OUT” or SUB = Use the Sub Input

“IN” or F/R = Use the Front and Rear inputs as its signal will be summed then sent to the sub channel of the amplifier

HPF/LPF/SUBSONIC CROSSOVER FREQUENCY

Controls the crossover points for the speaker outputs.

REAR X-OVER CONFIG

HP: High pass crossover is on

BP: Low and high pass crossovers are both on, creating a Bandpass (BP) filter for midbass/midrange drivers. Check on page 4 (Ti2 1000.4) for more details on how to use the the BP setting for a fully active crossover system.

SENS

Used to reach maximum amplifier power with a wide variety of headunits.

REMOTE BASS LEVEL CONTROL (RBCF)

This port is for connecting the remote subwoofer level control. This allows up to 20dB of volume adjustment for the subwoofer channel. This is not a bass boost, it controls the level of the low pass signal.

PHASE

This allows the phase of the subwoofer output to be adjusted from 0 to 180 degrees. This adjustment can help achieve better “up front” subwoofer bass and resolve subwoofer cancellation problems in certain installations. Each installation is different, slowly adjust and listen for best results.

+12V

This must be connected to the fused positive terminal (+12V) of the car’s battery. The fuse must be located within 18 inches of the battery.

REMOTE

This must be connected to switched +12V, usually a trigger wire coming from the head unit or ignition.

GROUND

This must be connected to the negative terminal of the car’s battery or bolted to a clean, unpainted part of the chassis of the vehicle.

REMOTE MONITORING DISPLAY (RMD)

Connect optional RMD Voltage Display to this port.

SPEAKER OUTPUTS

Used to connect the amplifier to speakers. Ti2 1600.5’s minimum impedance is 4 ohms bridged or 2 ohms stereo on front and rear channels. Use the Left + and Right - to bridge the channels. Minimum impedance is 2 ohms for the subwoofer channel and its not bridgeable.

CLIP INDICATORS (located on top of the amplifier)

Lights when the amplifier reaches near maximum output. Under heavy use the clip indicators should be flashing during the peaks of the music. The clip indicator should not stay lit for long periods of time (more than 1 or 2 seconds), if this is the case you need to reduce system volume or the SENS level of the amplifier.

www.phoenixgold.com

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Amplifier Manual Manual DEL Amplificador Models Ti2 1000.4, Ti2Ti2 1000.4 Specifications SpecificationsKEY Features Channel Power Amplifier Rear X-OVER Config SUB Input SwitchPhase FRONT, Rear and SUB InputsRear HP Rear LP TI2 1000.4 Crossover SettingsSubsonic Installation NOTESTI2 1600.5 Crossover SettingsAmplificador DE Potencia DE 4 Canales Entradas Amplificador DE Potencia DE 5 CanalesHPF/LPF Frecuencia de Crossover SUB Seleccion DE EntradeBorne Télécommande ConfigEntrée NiveauSélection D’ENTRÉE SUB Commande À Distance DU Niveau DES BassesInternational Warranties Limited Warranty on Amplifiers

TI2 1000.4, TI2 1600.5 specifications

The Phoenix Gold TI2 series amplifiers, specifically the TI2 1600.5 and TI2 1000.4, are designed to deliver exceptional audio performance for car audio enthusiasts. These amplifiers have been engineered to meet the demanding needs of modern automotive sound systems, combining power, efficiency, and advanced technology.

The TI2 1600.5 is a powerful 5-channel amplifier that offers a robust output of 1600 watts. This model is particularly suited for those looking to drive multiple speakers and a subwoofer simultaneously, making it an ideal choice for comprehensive sound setups. The amplifier features a high-pass filter and a low-pass filter, allowing users to customize their sound to suit their preferences. With a compact size, it easily fits into tight spaces in any vehicle while maintaining a rugged build quality that can withstand the rigors of daily use.

On the other hand, the TI2 1000.4 is a 4-channel amplifier delivering 1000 watts of power, perfect for driving full-range speakers. It incorporates high-performance circuitry that ensures minimal distortion, maximizing sound clarity and impact. Both the TI2 1600.5 and TI2 1000.4 benefit from Phoenix Gold’s proprietary technology, such as the Delta Class D amplification system that enhances efficiency, reduces heat generation, and increases overall output.

Key features include an adjustable gain control, allowing users to fine-tune the output to match their specific audio needs. The amplifiers come equipped with a built-in bass boost, which enhances low-frequency sounds for a more dynamic listening experience. Additionally, each model boasts a thermal protection circuit that prevents overheating, ensuring reliability during extended use.

Both the TI2 1600.5 and TI2 1000.4 are compatible with a variety of input sources, making them versatile solutions for different audio setups. They also include high-level inputs, allowing easy integration into factory stereo systems without the need for a dedicated line-out converter.

Whether you are aiming for loud, powerful bass or crystal-clear highs, the Phoenix Gold TI2 series amplifiers provide the performance and flexibility necessary to elevate your car audio experience. With their advanced features and dependable technology, they stand out in the competitive world of automotive audio enhancement.
Top Page Image Contents