Orion Car Audio HCCA52, HCCA62 owner manual Installing the Tweeter, Surface Mounting

Page 5

Step 7: Pull the wire through the speaker opening and connect to the speaker.. Be sure to observe proper mid/woofer polarity during this process..

Step 8: Mount the speaker- Place the speaker and the grille in the installation hole.. Align the mounting screw holes and drive in the four mounting screws..

Installing the Tweeter

SURFACE MOUNTING

Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location..

Step 2: Place the provided template or tweeter cup against the panel and mark the two holes at the rear of the housing..

Step 3: Drill the smaller holes using a 1/8" drill bit.. These are the mounting screw holes..

WARNING: Check for clearance of window mechanisms and electrical wires BEFORE you drill..

Step 4: Drill the larger off-center hole using a 3/8" drill bit, insert a grommet and route the speaker wire from the crossover through the grommet..

Step 5: After removing the surface mount tweeter assembly trim ring, route the tweeter wires through the larger hole in the housing and connect to the speaker wires from the crossover.. (See Figure 4..)

Step 6: Insert the excess speaker wire into the hole and position the housing so the housing will not pinch the wires after final mounting..

Step 7: Attach the housing using the supplied screws of the correct length for a solid mount..

Step 8: Insert the tweeter into the housing and attach the surface mount trim ring..

SURFACE

MOUNTING SCREWS

MOUNT

 

TRIM RING

 

 

 

SURFACE MOUNT HOUSING

Figure 2

 

Figura 2

 

Abbildung 2

TWEETER

TWEETER WIRE

PANEL

WIRING HARNESS

4

© 2010 directed electronics—all rights reserved

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Component Speaker Introduction Table of ContentsPractice Safe Sound InstallationWhat’s in the Box Tools of the TradeFinding Speaker Mounting Locations Installing the Mid/WoofersDoor Mounting Rear Deck MountingSurface Mounting Installing the TweeterFull Flush Mounting Installing the CrossoverParallel Wiring Bi-Amp Wiring HCCA52 HCCA62 SpecificationsFeatures Français Installation DES HAUT-PARLEURS Médiaux ET DE GravesOÙ Monter LES HAUT-PARLEURS Montage SUR UNE PortièreMontage Encastré Installation DU HAUT-PARLEUR DaigusMontage EN Surface Installation DU Répartiteur Caractéristiques SpécificationsUbicaciones DE Montaje DE LOS Altavoces EspañolMontaje EN LA Puerta Montaje EN LA Repisa TraseraMontaje AL RAS Instalación del TweeterMontaje EN Superficie Instalación DEL Crossover Características EspecificacionesSO Platzieren SIE DIE Lautsprecher DeutschTüreinbau Einbau IM KofferraumBündiger Einbau Einbau des HochtönersOberflächeneinbau Installation DER CROSSOVER-EINHEIT Eigenschaften DatenItaliano Installazione DEI MIDRANGE/WOOFERMontaggio Sulle Portiere Montaggio NEL Piano Portaoggetti PosterioreMontaggio a Filo Installazione del tweeterMontaggio a Superficie Installazione DEL Crossover Caratteristiche Dati TecniciDeterminação DOS Locais Para Instalação DOS ALTOS-FALANTES PortuguêsInstalação NAS Portas Instalação no Painel TraseiroInstalação Embutida Instalação do tweeterInstalação NA Superfície Instalação do Crossover Especificações Warranty

HCCA62, HCCA52 specifications

Orion Car Audio has long been recognized for its commitment to high-quality sound and innovative technology. Their HCCA series, particularly the HCCA52 and HCCA62 models, epitomize this dedication by combining impressive power handling with advanced design features. The HCCA52 is a 5.25-inch speaker that offers an astonishing balance between size and sound performance. It is designed to deliver high output levels while maintaining clarity and precision across a wide frequency range. With a peak power handling of 400 watts and an RMS rating of 200 watts, this speaker is capable of filling any vehicle with exceptional audio quality without distortion.

One of the standout features of the HCCA52 is its lightweight, yet sturdy, polypropylene cone, which contributes to the speaker's efficiency and durability. The cone is paired with a high-quality rubber surround, which enhances the speaker's longevity while allowing for significant excursion. The treated cloth dust cap aids in reducing unwanted resonances, allowing for a clearer sound performance. Additionally, the oversized voice coil increases power handling and ensures reliability during high-volume playback.

On the other hand, the HCCA62 is a 6.5-inch model that caters to those seeking a more robust performance. With an impressive peak power handling of 600 watts and an RMS of 300 watts, the HCCA62 can accommodate larger vehicles and bigger sound requirements. The drive system utilizes a similar polypropylene cone and rubber surround configuration found in its smaller counterpart, ensuring durability and responsiveness.

Both models feature advanced technologies such as vented pole pieces that enhance cooling and increase efficiency, leading to longer playtime without risking damage from overheating. The HCCA series also benefits from a unique tweeter design, which allows for extended high-frequency response and excellent imaging. By utilizing neodymium magnets, the tweeters provide crisp treble that complements the rich bass produced by the main speakers.

Other characteristics include high sensitivity ratings, which ensure that these speakers can produce loud volumes with less power input, making them ideal for use with various head units and amplifiers. The HCCA series is also engineered for easy installation, featuring versatile mounting options that fit seamlessly into a wide range of vehicle models.

In summary, the Orion Car Audio HCCA52 and HCCA62 are engineered for audio enthusiasts seeking exceptional sound quality, durability, and performance. Their combination of innovative design, powerful handling capabilities, and advanced technologies make them a top choice for those looking to upgrade their car audio system.
Top Page Image Contents