Kenwood DPF-R6010 Case of difficulty, Operation to reset, CD player unit, Remote control unit

Page 25

In case of difficulty

CD-206/204/203/DPF-R6010/R4010/R3010 (En)

 

What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table

 

below to see if the problem can be corrected before seeking help from your dealer or service representative.

25

 

Operation to reset

The microcomputer may malfunction (impossibility to operate, erroneous display, etc.) when the connection cords are un- plugged while the unit is ON or due to an external factor. In this case, execute the following method to reset the microcomputer and return it to normal condition.

Unplug the power cord from the power socket and plug the power cord into the socket again.

ÖPlease be aware that resetting the CD player will erase all stored information and return it to the factory settings.

CD player unit

Symptom

Cause

Remedy

 

 

 

 

The unit is not turned ON with the ON/

ÖPower plug is loosely connected.

ÖInsert the power plug firmly to the AC outlet.

STANDBY (POWER/

 

 

) switch ON.

ÖWith the power plug connected to the switched

ÖTurn the amplifier’s power ON.

 

 

 

 

 

 

 

AC outlet of an amplifier, the power of the

 

 

 

 

 

 

amplifier is turned off.

 

 

 

 

 

There is no sound even when a disc is loaded.

ÖDisc is loaded upside down.

ÖLoad the disc again with its label side up.

 

 

 

 

ÖDisc is loose.

ÖInsert disc properly.

 

 

 

 

 

ÖDisc is dirty.

ÖWipe off the dust on the surface of the disc

 

 

 

 

 

referring to “Disc handling precautions”.¢

 

 

 

 

ÖDisc is cracked.

ÖReplace the disc with a new one.

 

 

 

 

 

ÖCondensation has occurred on the optical lens

ÖRemove any condensation from the unit by

 

 

 

 

unit.

referring to the section entitled, “Caution on

 

 

 

 

ÖPlay mode is not entered.

condensation”.

¢

 

 

 

 

ÖPress the 6 key.

 

 

 

 

 

ÖThe connection cords are inserted loosely.

ÖConnect all connection cords firmly.

 

 

 

 

 

ÖOutput level is attenuated too low.

ÖAdjust the output level with OUTPUT key on

 

 

 

 

 

the remote control unit.

5

 

 

 

Music is interrupted. (Sound is skipped.)

ÖDisc is too dirty.

ÖWipe off the dust on the disc surface referring

 

 

 

 

 

to “Disc handling precautions”.

¢

 

 

 

 

ÖDisc is cracked.

ÖReplace the disc with a new one.

 

 

 

 

 

ÖOscillation is applied to this unit.

ÖTry selecting a place where no strong vibrations

 

 

 

 

 

occur by changing the installation place, etc.

 

 

 

Play begins as soon as the unit is turned ON.

ÖThis unit is designed so that play begins auto-

ÖIf automatic play is not required remove the

 

 

 

 

matically when the unit is turned ON if a disc is

disc from the player before setting the unit to

 

 

 

 

already loaded.

STANDBY mode.

 

 

 

 

 

 

 

 

Remote control unit

Symptom

Cause

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Remote control operation is not possible.

ÖBatteries are exhausted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ÖReplace with new batteries.

8

 

 

ÖThe remote control unit is too far away from the

 

ÖOperate the remote control unit

within the

 

main system, controlling angle is too large, or

 

 

controllable range.

8

 

 

there is an obstacle in between.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For the U.S.A.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CAUTION:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KENWOOD CORPORATION

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Use of controls or adjustment or performance of procedures other than

2967-3, ISHIKAWA-CHO, HACHIOJI-SHI,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TOKYO, JAPAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

those specified herein may result in hazardous radiation exposure.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

KENWOOD CORP. CERTIFIES THIS EQUIPMENT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In compliance with Federal Regulations, following are reproductions of

 

CONFORMS TO DHHS REGULATIONS NO. 21

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

labels on, or inside the product relating to laser product safety.

 

CFR 1040.10, CHAPTER I, SUBCHAPTER J.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Location: Back Panel

Page 24 Page 26
Image 25
Page 24 Page 26
Contents DTS disclaimer clause CD/DPF-R SeriesSafety precautions Introduction Before applying powerMarking of products using lasers Except for some areas AC voltage selectionContents Malfunction of microcomputer System connectionsConnection to digital amplifier or MD CD-206/DPF-R6010 only System connections Output -12dBTo use the headphone Except for CD-203/DPF- R3010 About the Standby mode Controls and indicatorsControls and indicators Operation Loading batteriesIllustration shows the RC-P0601 Load/unload a disc Disc Reading D1 CD TextClose the tray Mode Start playback Normal play Track modePlaying tracks in order from track No 123PGM01 Edit Rndm D1 02 Title XYZ D1 01 Title ABCTitle XYZ Display scrollingAbcdef Disc Title ABArranger Abcd Selecting the text information display Text DisplayPGM01 DISC? Programmed play PGM modePGM01 D1 TNO.?? PGM01 D1 TNO.25PGM01 D5 TNO.25 Programmed play PGM modeTo stop playback To add a track to the programAuto space function To clear tracks from the programTime display on CD player Time Disp Rndm Playback in a random order Random playbackPreparation Ing oneRepeat on Repeated playbackTo repeat only the programmed tracks Repeat PGM01 \Repeat OFF Normal Edit EditingEdit DISC? Edit DISC3 C-46Editing Press so that the Multi Edit indicator lightStart recording Repeat ,4 abovePlaying or recording the edited contents To check the edited contentsTo clear the edited contents Edit aSet the amplifier volume Timer operationsSet the timer on time PreparationDisc MaintenanceRemote control unit Operation to resetCase of difficulty CD player unitSignal to noise ratio SpecificationsVariable CD-204/DPF-R4010 Headphone output MaxCD-206/204/203/DPF-R6010/R4010/R3010 En For your records

DPF-R4010, DPF-R6010, DPF-R3010 specifications

Kenwood, a well-recognized name in audio and home entertainment equipment, has expanded its portfolio with several high-quality digital photo frames, namely the DPF-R3010, DPF-R6010, and DPF-R4010. Each of these models combines stylish design with modern technology, providing users with an engaging way to display their cherished memories.

The Kenwood DPF-R3010 is an entry-level model equipped with a 10.1-inch display that boasts a resolution of 1024 x 600 pixels. This frame is perfect for those who want an easy-to-use device for showcasing photos. It supports various image formats, including JPEG and BMP, and features a built-in memory of 4GB, allowing for a substantial number of photos. Users can connect via USB or SD card, making it versatile for transferring images. The DPF-R3010 also includes an adjustable brightness feature, ensuring that images are clear and vibrant in any lighting condition.

Stepping up in the lineup, the Kenwood DPF-R4010 offers a more expansive display at 12 inches, featuring an impressive resolution of 1280 x 800 pixels. This enhanced display quality makes it ideal for showcasing high-resolution photographs. The DPF-R4010 also comes with a variety of slideshow options, allowing users to customize how their photos are presented. It supports both USB and SD card connections, as well as a dedicated remote control for added convenience. With its sleek design, the DPF-R4010 fits seamlessly into any home décor.

The Kenwood DPF-R6010 represents the pinnacle of this series with its 15-inch display and a high resolution of 1920 x 1080 pixels. This model is designed not only for photo display but also for video playback, adding a dynamic element to any slideshow. The DPF-R6010 boasts Wi-Fi connectivity, allowing users to stream images directly from their smartphones or social media accounts. With advanced features such as motion sensors, this frame automatically wakes up when someone enters the room, ensuring that every moment is showcased without manual effort.

All three models share standard features such as calendars and clocks, making them multifunctional devices. With their elegant aesthetics and modern technology, the Kenwood DPF series offers a compelling way to keep memories alive, whether you're choosing the economical DPF-R3010, the versatile DPF-R4010, or the feature-rich DPF-R6010. Each model is designed to cater to a range of user needs while ensuring photo display is both an art and a joy.
Top Page Image Contents