a/d/s/ 336im manual Jack pinouts Specifications, System planning, 334im 335im 336is

Page 5

jack pinouts

specifications

 

334im

335im

336is

frequency response +/-3dB:

48Hz to 22kHz

48Hz to 22kHz

40Hz to 22kHz

sensitivity 2.83 volt RMS pink noise measured at 1 meter:

85dB

90dB

91dB

impedance, nominal:

4 Ohms

4 Ohms

4 Ohms

recommended amplifier power watts RMS:

15 to 100

15 to 100

15 to 150

dimensions – woofer/midrange transducer

 

 

 

mounting depth (woofer):

2” / 50mm

2 3/8” / 60mm

2 7/16” / 63mm

overall height:

2 5/16” / 59mm

2 11/16” / 69mm

2 15/16” / 79mm

overall maximum diameter:

4 7/8” / 123mm

6” / 152mm

6 1/2” / 165mm

maximum height above panel without grille:

11/16” / 18mm

1/2” / 13mm

5/8” / 16mm

maximum height above panel with grille:

3/4” / 20mm

3/4” / 20mm

15/16” / 24mm

maximum grille diameter:

5 3/16” / 132mm

6 1/2” / 166mm

7 1/8” / 181mm

cutout size:

 

4 5/8” /118mm

4 15/16” / 125mm

dimensions – crossover network

 

 

 

length/width/height:

5 3/16” x 3 1/2” x 1 5/8” 132mm x 89mm x 42mm

Thiele-Small specifications

 

 

 

free air resonance (Fs):

52.0Hz

57.2Hz

57.1Hz

electrical damping (Qes):

.82

.34

.47

mechanical damping (Qms):

4.50

4.87

6.00

total damping (Qt):

.69

.32

.44

equivalent volume of compliance (Vas) cubic feet / liters:

0.19 / 5.5

0.26 / 7.41

0.46 / 13.0

effective cone area (Sd) in2:

8.56

14.1

18.9

center to peak linear excursion (Xmax):

.16” / 4.0mm

.16” / 4.0mm

.16” / 4.0mm

peak to peak excursion:

1/2” / 12.7mm

1/2” / 12.7mm

3/4” / 19.0mm

voice coil DC resistance (Re):

3.1

3.1

3.1

voice coil diameter:

1” / 25.4mm

1” / 25.4mm

1” / 25.4mm

voice coil length (winding length):

.45” / 11.5mm

.45” / 11.5mm

.45” / 11.5mm

a/d/s/ subscribes to the philosophy of continuous product development therefore the specifications may change without notice.

a/d/s/ tweeters are constructed in concert with the Ferrosound program and use Ferrofluid to provide increased power handling, decreased distortion, minimum electrical impedance change, higher linearity, and smoother frequency response.

16

warnings and tips

Study your automobile thoroughly before you drill or cut any holes. Take extra care when working near gas tanks, gas lines, brake or hydraulic lines and electrical wiring.

Wear eye and ear protection when using power tools.

Keep the woofers and tweeters away from metal filings and shavings. Once foreign objects are stuck to the magnets or tweeter dome, it will be virtually impossible to remove them. Keep the tweeters in their protective bags until final mounting to prevent any possibility of metal dust or chips from passing through the grille and accumulating on the dome.

Exercise caution when working with the 3-series with the grille removed. A slip of the hand with a screwdriver or other tool can result in irreparable damage to the cone or dome. Do not touch the cone or dome.

Do not install the components where they will be subject to excessive heat, moisture or dust; or where they will be kicked or repeatedly bumped or brushed.

Make absolutely sure that the woofer is connected to the lowpass output and the tweeter is connected to the highpass output of the crossover network. If these connections are reversed, low-frequency signals will be fed to the tweeter without fuse protection. In this case, the tweeter may be damaged. Such damage is not covered by the warranty.

When removing or installing the grille on the 3-series, be careful not to brush the woofer’s rubber surround or the tweeter’s dome with the edge of the grille. Cutting or tearing the surround or dome will destroy the unit.

Never run wires outside or beneath the vehicle where they can be snagged by road hazards or the moving parts of the vehicle. Use existing wire channels, sills, panels and molding strips inside the automobile to hide the wiring for neat appearance and safety.

Make sure your radio/cassette/cd player and or other equipment is turned off while connecting the 3-series speaker terminals. Turn on the various components and slowly advance the volume control only after checking and double checking all connections

Note: if sound is weak or distorted, immediately turn down the volume and see the section entitled troubleshooting.

system planning

Proper system planning is the best way to maximize performance. By planning your installation carefully you can avoid situations where the performance or reliability of your system is compromised. Your authorized a/d/s/ dealer has been trained to know how to maximize your systems sonic potential. They are a valuable resource in helping you with your system design and installation.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 334im 335im 336im European contact Declaration of conformityAbout this manual Table of contentsIntroduction Warranty information Features of your 3-series loudspeaker334im 335im 336is Jack pinouts SpecificationsSystem planning Amplifier requirements TroubleshootingMounting locations Controls and connectionsSpeaker wiring Speaker mounting Connecting the system Crossover installationBi-wiring / bi-amping Rotating the tweeter

336im, 334im, 335im specifications

The A/D/S series of amplifiers, specifically the models 335IM, 334IM, and 336IM, have made a significant mark in the world of audio technology, particularly in providing high-quality sound amplification for various applications. Each of these models integrates advanced features designed to enhance the listening experience, making them popular choices among audiophiles and professionals alike.

The A/D/S 335IM amplifier is renowned for its impressive power output, delivering robust performance while maintaining excellent audio quality. It typically features a Class A/B design, allowing it to provide warmth and clarity in sound. The 335IM is equipped with several inputs and outputs, making it versatile for both home theater setups and professional audio environments. Its built-in protection circuitry ensures reliability and prevents damage from overloads or overheating, extending the amplifier's lifespan.

Moving to the A/D/S 334IM, this model is often celebrated for its compact design and lightweight construction, making it easier to integrate into various audio setups. Despite its smaller form factor, the 334IM does not compromise on sound fidelity, delivering crisp highs and deep lows that satisfy even the most discerning listeners. It employs advanced signal processing technologies, which help in minimizing distortion and enhancing overall sound clarity.

Meanwhile, the A/D/S 336IM amplifier stands out with its advanced digital signal processing capabilities. With features like customizable audio settings and built-in equalization, the 336IM allows users to tailor their audio experience to their specific preferences. This model usually supports multiple audio formats, making it an excellent choice for modern home theater systems that rely on digital audio sources. Its efficient power management system ensures that audio performance remains optimal while reducing power consumption.

In summary, the A/D/S 335IM, 334IM, and 336IM amplifiers each bring unique strengths to the table. While the 335IM excels in power and reliability, the 334IM offers compactness without sacrificing sound quality. The 336IM, with its advanced digital features, caters to tech-savvy users looking for customization. Together, they exemplify A/D/S's commitment to delivering high-performance audio technology. These amplifiers represent a blend of quality, innovation, and user-friendly design, making them valuable assets for any audio setup.
Top Page Image Contents