JL Audio XD200/2 owner manual Speaker Outputs, Or a summed mono center channel

Page 10

SPEAKER OUTPUTS

The XD200/2’s speaker outputs are designed to accept 16 AWG - 8 AWG wire. To connect the speaker wires to the amplifier, first back out the set screws on the top of the terminal block, using the supplied 2.5 mm hex wrench. Strip 1/2 inch (12 mm) of insulation from the end of each wire and insert the bare wire into the terminal block, seating it firmly so that no bare wire is exposed. While holding the wire in place, tighten the set screw firmly, taking care not to strip the head of the screw.

The XD200/2 is designed to deliver power into speaker loads equal to or greater than 2 ohms when using a “stereo” configuration and speaker loads equal to or greater than 4 ohms when using a “bridged” configuration.

Speaker loads below 2 ohms nominal per channel (or 4 ohms bridged) are not recommended and may cause the amplifier to initiate a protection mode which reduces power output.

BRIDGING CONSIDERATIONS Bridging is the practice of combining the

output of two amplifier channels to drive a single load. When bridged, each channel produces signals of equal magnitude, but opposite polarity. The combined output of the two channels provides twice the output voltage available from a single channel. The XD200/2 has been designed for bridging of its channel pair without the need for input inversion adaptors.

To bridge the XD200/2, use the “Left +” and “Right speaker connectors only (the

Left and “Right +” remain unused). When bridged, the amplifier will deliver optimum power into a 4 ohm load.

When the XD200/2 is bridged, it

will deliver 200W x 1 into a 4 ohm load or 150W x 1 into an 8 ohm load. Operating a bridged XD200/2 into a load lower than 4 ohms is not recommended. Because a bridged pair of channels requires that both channels receive input, you need to connect both left and right inputs to the source unit. Connection of only one input will result in reduced power output, increased distortion and can cause the amplifier to overheat. Do not do this!

When the XD200/2 is operating in bridged mode, the output will be in mono (only one channel). This mono channel can contain right channel only information, left channel only information or the sum of the information from both the right and left channels. In order to achieve one of these options, configure the inputs to that pair of channels in one of these two ways:

1)Left Channel Only or Right Channel Only Information: If you wish to send a left-only or right-only signal to the XD200/2, use a “Y-Adaptor” to split the single channel signal into both left and right RCA inputs. This option is useful when using one XD200/2 to drive left channel speakers only and the another XD200/2 to drive right channel speakers only.

2)Left + Right Channel Information: When bridged and fed by a stereo input, the XD200/2’s channels will automatically combine the left a nd right channels into a summed mono (left + right) channel. This option is useful when using a bridged XD200/2 to drive a subwoofer system

or a summed mono center channel.

10 JL Audio - XD200/2 Owner’s Manual

Image 10
Contents 200W 2-Channel Amplifier Protect Your Hearing Installation ApplicationsSerial Number Cooling Efficiency Considerations Planning Your InstallationSafety Considerations A fan. In normal applications, fan-cooling is not necessaryProduct Description Securely mount the amplifierPower Connections Fuse RequirementsInput Section TURN-ON LeadInput Voltage Range Input Sensitivity Control To achieve the desired system balanceFilter Controls Most speakers are not designed to reproduceRemote Level Control Optional PreoutsSpeaker Outputs Or a summed mono center channelServicing Your JL Audio Amplifier Problem and turn the volume upJL Audio Technical Support Necessary Equipment Nine-Step ProcedureAppendix a Turn the Input Sens. control all the way downAppendix B  Appendix CAppendix D Troubleshooting My amplifier doesn’t turn onMy amplifier turns on, but there is no output INSTALLATION NOTES Page Page Page JL Audio, Inc Limited Warranty Amplifiers USAIf you need service on your JL Audio product International Warranties