JL Audio SB-T-TUNDCMAX/13TW5 warranty C L U D E D H a R D W a R E P E R S T E a L T H B O, E P 2

Page 4

 

INTERIOR PLASTIC TRIM PANEL

REMOVEABLE INTERIOR

 

REAR WALL

STEALTHBOX®

 

FENDER WASHER

COMPLETED IN

 

STEP 16

HEX NUT

 

LOCK WASHER

 

FRONT OF TRUCK

S T E P 1 8

This is a cross-sectional drawing showing the bolt from step 13 also passing through the interior plastic trim panel and the Stealthbox®. The bolt then holds the Stealthbox® in place via the fender washer, split lock washer and, nut. Again, be cautious not to overtighten the nut, it only needs to be snug.

SB-T-TDCMAX/13TW5 INSTR_SKU# 011266

I N C L U D E D H A R D W A R E P E R S T E A L T H B O X ®

(1)3/8-16 X 1 1/2" Hex Head Bolt

(3)3/8 X 1 1/4" Fender Washer

(2)3/8" Split Lock Washer

(2) 3/8 X 16 Hex Nut

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 13TW5-3

Nominal Impedance: 3 ohms mono

Continuous Power Handling: 600 Watts

Page 4 • JL Audio, Inc 2008

S T E P 1 9

We suggest wiring the enclosure at this point, it will be very hard (or impossible) to access the terminal cup if the second Stealthbox® is installed. Route the wire using a safe, secure method to the amplifier location. Always ensure that wires cannot be pinched or damaged along the path to the next component.

If installing two Stealthboxes®, we suggest wiring the second enclosure before mounting as the terminals will be much more accessible than after the enclosure is mounted. Repeat steps 17-19for the second Stealthbox®.

S T E P 2 0

Place the bottom edge of the woofer on the enclosure, attach wires to the appropriate connectors. Lean the woofer back into location and make sure that wires do not get pinched either betwen the woofer and the enclosure or the securing hardware.

S T E P 2 1

Use a sharp pointed object to align the woofer with the holes previously used to mount it, re-mount the woofer. Use a “crossing “ pattern as if re-mounting a repaired flat tire. If installing two Stealthbox ® enclosures, repeat this procedure in both enclosures. Again, the grilles did not need to be removed!

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an amplifier recommendation and basic set-up help.

P o w e r R e c o m m e n d a t i o n

JL Audio recommends using a high quality amplifiers such as the JL Audio 500/1v2. The 500/1v2 could be used for one or, two Stealthboxes. The ideal amplifier for two enclosures is the HD750/1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2 when being used to power your Stealthbox®.

Preamp Output Section

Infrasonic Filter

"Q"

Center Freq.

Boost (dB)

Amp LP Filter

Amplifier Input Section

Subwoofer Output

Output Mode

Filter Slope

 

1.6

 

45

 

+10

Mode / Slope

Input Voltage Input Sens. Signal Sensing

 

 

 

1.1

2.7

35

55

+4

+13

 

 

 

0.7

25

70

Full Range / Amp Filter / Out Filter

12dB / 24dB

 

 

Off / 30Hz

0.5

4.3

20

85

 

0

+15

Off / 12dB / 24dB

Low / High

Off / On

 

_

_

+12VDC Ground Remote

 

65

 

 

Filter Mode

 

30

 

Bass EQ

 

 

 

 

 

 

 

65

 

 

+

+

 

55

85

 

 

25

40

 

 

 

 

Advanced

55

85

 

 

 

45

 

 

120

 

 

18

 

50

 

 

 

 

 

 

 

 

45

 

120

 

 

 

JL AUDIO 500/1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bass

 

 

 

 

 

 

 

 

 

 

40

200

LP / HP

15

60

 

Off / On

 

 

 

 

Control

40

200

 

MONO OUTPUT ONLY

five-channel system amplifier

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Left Ch.

Right Ch.

Filter Freq. (Hz)

 

 

Infrasonic Freq. (Hz)

 

 

 

 

Remote Bass Port

 

 

Filter Freq. (Hz)

Left Ch.

Right Ch.

 

 

 

The JL Audio 500/1v2 and the HD750/1 are very versatile audio components. Please consult the owner’s manual for even more detailed information about installing and tuning these amplifiers.

M I D / H I G H F r e q u e n c y D r i v e r F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle.

Dash Speaker Size / JL Audio Model: 3.5” - TR350-CXi

Front Speaker Size / Location: 6”x 9” - Front Doors

Fits JL Audio Models: TR690-TXi, VR690-CXi

Rear Speaker Size / Location: 6.5” - Rear Door

Fits JL Audio Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi,

C5-650, C5-650x, ZR650-CSi

(954) 443-1100

 

www.jlaudio.com

 

 

 

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

 

 

 

 

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

 

 

 

 

JLA-SKU# 011266 8-12-2008 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479

 

 

 

 

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

 

 

 

 

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y

•

M I R A M A R , F L O R I D A

•

3 3 0 2 5

•

U S A

Page 3 Page 4
Image 4
Page 3 Page 4
Contents E P Estimated TimeTest Stealthbox for proper operation before continuing E P 6 d e t a i l Please follow safe drilling proceduresE P 1 E P 1 2 d e t a i l 3 JL Audio, IncC L U D E D H a R D W a R E P E R S T E a L T H B O E P 2W e r R e c o m m e n d a t i o n D / H I G H F r e q u e n c y D r i v e r F I T M E N T

SB-T-TDCMAX/13TW5, SB-T-TUNDCMAX/13TW5, SB-T-TUNDCMAX/13TW5/DG specifications

The JL Audio SB-T-TUNDCMAX/13TW5 is a premium subwoofer enclosure specifically designed for the 2007-2021 Toyota Tundra. This enclosure is engineered to accommodate the 13TW5 subwoofer, which is renowned for its compact design and high-performance capabilities. JL Audio has mastered the balance between size and sound, making this setup an excellent choice for truck owners who desire powerful bass without sacrificing valuable cargo space.

One of the standout features of the SB-T-TUNDCMAX/13TW5 is its unique fiberglass construction. This durable material is engineered to provide excellent acoustic properties, ensuring that sound waves are efficiently produced without distortion. The enclosure is designed to fit snugly under the rear seat of the Tundra, maintaining a factory look while keeping the subwoofer secure and protected from the elements.

Another impressive characteristic of the SB-T-TUNDCMAX series is the 13TW5 subwoofer itself. This dual 2-ohm voice coil subwoofer features a shallow mounting depth, allowing it to fit into tight spaces while still delivering astonishing sound quality. With a peak power handling of 1,000 watts and RMS power handling of 600 watts, the 13TW5 is capable of producing deep, resonant bass that can fill any cabin with adequate low-end frequencies.

The design of the SB-T-TUNDCMAX system emphasizes low-frequency response and efficiency. The enclosure is meticulously tuned to provide the ideal air space for the subwoofer, ensuring maximum performance and minimal distortion. The subwoofer's patented technology includes a durable, cast-alloy frame that reduces flex and enhances overall sound clarity.

Additionally, the enclosure is equipped with a sleek, automotive-grade finish, enhancing the aesthetic appeal and making it a perfect addition to any Tundra. The overall integration of design, technology, and construction ensures that the SB-T-TUNDCMAX/13TW5 delivers not just sound, but a profound auditory experience that resonates with truck enthusiasts looking for a premium audio solution.

In conclusion, the JL Audio SB-T-TUNDCMAX/13TW5 is a top-tier subwoofer and enclosure combination that stands out in the realm of automotive audio. Its innovative design, powerful subwoofer, and commitment to sound quality ensure that Tundra owners experience the best in car audio, providing compelling bass that transforms any driving experience.
Top Page Image Contents